Оценок - 3, средний балл: 4 ( )

Производитель: Cannon Размер: 179.57 kb Название файла: CHICHESTER_PRO-600.pdf Язык инструкции:

1. The rear wheels can be raised or lowered from the BACK of the cooker by adjusting the levelling screws ‘A’ in the plinth. 2. The front feet can be simply screwed in or out to lower or raise the front of the cooker. CAUTION: Some soft floor coverings may get damaged if the cooker is not moved carefully. VIEWED FROM THE REAR STABILITY BRACKET The back of the cooker has a slot for engagement of a stability bracket, which can be obtained, as an extra, from your cooker supplier. STABILITY BRACKET POSITION SLOT FOR STABILITY BRACKET REAR OF COOKER INSTALLATION INSTRUCTIONS CONNECTING TO GAS SUPPLY The cooker is designed to match the depth of standard 600mm worktops. An adaptor backplate should, therefore, be fitted within the shaded area shown to allow the cooker to be pushed fully to the wall. 40mm 30mm 220mm 70mm 635mm 450mm GAS BACKPLATE POSITION Connection to the cooker should be made with an approved appliance flexible connection to BS 669. A length of 0.9 to 1.25m is recommended. The length of hose chosen should be such that when the cooker is in situ, the hose does not touch the floor. LPG models should be connected with a hose suitable for LPG and capable of withstanding a pressure of 50 mbar. The temperature rise of areas at the rear of the cooker that are likely to come in contact with the flexible hose do not exceed 70°C. ELECTRICAL CONNECTION WARNING – THIS APPLIANCE MUST BE EARTHED. CONNECT TO A 230-240V A.C. SUPPLY ONLY. Connection to the electricity supply should be made via a properly earthed, readily accessible wall socket which is adjacent to but not directly above, and not more than 1.25m away from the appliance and capable of electrical isolation. The mains lead should be routed such that it cannot touch hot parts of the cooker i.e. the back panel above a height of 650mm from the floor. Should this plug not fit the socket outlet in your home it should be cut off and replaced with a suitable plug as outlined below. NOTE: The removed plug cannot be used for any other appliance and should therefore be properly disposed of and not left where children might find it and plug it into a supply socket – with the obvious consequent danger. IF THE FITTED PLUG IS REMOVED The flexible mains lead must be correctly connected as below to a three pin plug of not less than 13 amp capacity. If a B.S. 1363 fused plug is used, it must be fitted with a 3 amp fuse which is approved to B.S. 1362. Green & IMPORTANT: The wires in the mains lead fitted to this Blue to Neutral Cord Clamp Yellow to Earth appliance are coloured in accordance with the following code: Brown to GREEN AND YELLOW – EARTH Live BLUE – NEUTRAL BROWN – LIVE 3 Amp Fuse As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:– The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured green or green and yellow. The wire which is coloured blue must be connected to the terminal which is marked with the N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. When wiring the plug, ensure that all strands of wire are securely retained in each terminal. Do not forget to tighten the mains lead clamp on the plug. As the appliance must be earthed, do not use 2-pin sockets outlets, if you are in doubt, consult a qualified electrician. Should the mains lead ever require replacement, it is essential that this operation be carried out by a qualified electrician and should only be replaced with a flexible cord of the same size i.e. 0.75mm2 cross sectional area and temperature rating of 85° C e.g. heat resisting PVC, available from our parts department (see Back Cover). IF A MOULDED PLUG IS FITTED In the event of replacing a fuse in the plug supplied a 3 amp ASTA approved fuse to BS1362 must be fitted. NOTE: The fuse cover must be refitted when changing the fuse. In the event of losing the fuse cover the plug must not be used until a replacement fuse cover has been obtained and fitted. A new fuse cover can be obtained from your local Electricity Board. The colour of the correct replacement fuse cover is that of the coloured marks or inserts in the base of the plug. Make sure that the cable does not become trapped when pushing the cooker into position. INSTALLATION INSTRUCTIONS INSTALLATION AND OPERATIONAL CHECKS After installation, check for gas soundness. The supply pressure can be checked at the grill injector. Access to the injector is by first removing the baffle at the front of the grill fastened by two screws. Then remove the fastening screw on the right hand side of the burner and slide the burner off the injector. Ensure that the grill burner is correctly located under the fixing screw on reassembly. Fit the hotplate burner bodies and caps, pan supports and shelf ...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: