Войти:
Оценок - 0, средний балл: 0 ( )

Инструкция по эксплуатации Brother, модель MFC-8840DN

Производитель: Brother
Размер: 3.21 mb
Название файла:
Язык инструкции:en
Перейти к скачиванию



К этому устройству также есть другие инструкции:

Фрагмент инструкции


—OR— Clear the data in the memory. (See Out of Memory message on page 10-5.) —OR— Add an optional memory. (See Memory board on page 13-1.) (Printing operation in process) Reduce print resolution. (See Print Quality in Software User’s Guide on the CD-ROM.) —OR— Clear the data in the memory. (See Out of Memory message on page 10-5.) —OR— Add an optional memory. (See Memory board on page 13-1.) No Response/Busy The number you dialed does not answer or is busy. Verify the number and try again. Not Registered You tried to access a One-Touch or Speed-Dial number that is not programmed. Set up the One-Touch or Speed-Dial number. (See Storing One-Touch Dial numbers on page 7-1 and Storing Speed-Dial numbers on page 7-2.) Pls Open A page, piece of paper or paper clip, etc. may Open the front cover. If you see any Cover be jammed inside the MFC. jammed paper or other item, gently pull it out, then close the front cover. If the error message remains, open and close the front cover again. If the MFC cannot reset itself and return to the date and time prompt, it will display Machine Error XX. Please call Brother Customer Service and tell them the Machine Error number: In USA: 1-800-284-4329 In Canada: 1-877-BROTHER No DX Tray You tried to make duplex printing with duplex cover open. Install the duplex tray correctly. (See Paper is jammed in the duplex tray (For MFC-8640D, MFC-8840D and MFC-8840DN) on page 12-11.) 12 -3 TROUBLESHOOTING AND ROUTINE MAINTENANCE ERROR MESSAGES ERROR MESSAGES CAUSE ACTION Paper Jam The paper is jammed in the MFC. See Paper jams on page 12-6 or Paper is jammed in the duplex tray (For MFC-8640D, MFC-8840D and MFC-8840DN) on page 12-11. Toner Empty Toner cartridge is not installed. —OR— Toner is used up and printing is not possible. Reinstall the toner cartridge. —OR— Replace the toner cartridge with a new one. (See Replacing the toner cartridge on page 12-28.) Toner Low If the LCD shows Toner Low, you can still print, however the MFC is telling you that the toner will soon run out. Order a new toner cartridge now. Original jams Based upon where the original is jammed, follow the appropriate set of instructions to remove it. Original is jammed in the top of the ADF unit. 1 Take out any paper from the ADF that is not jammed. 2 Lift the ADF cover. 3 Pull the jammed original out to the left. 4 Close the ADF cover. 5 Press Stop/Exit. TROUBLESHOOTING AND ROUTINE MAINTENANCE 12 - 4 Original is jammed inside the ADF unit. 1 Take out any paper from the ADF that is not jammed. 2 Lift the document cover. 3 Pull the jammed original out to the right. 4 Close the document cover. 5 Press Stop/Exit. —OR— 1 Take the ADF support out of the ADF unit. 2 Pull the jammed original out to the right. 3 Press Stop/Exit. 12 -5 TROUBLESHOOTING AND ROUTINE MAINTENANCE Paper jams Paper jams WARNING After you have just used the MFC, some parts inside the MFC are extremely hot. When you open the front cover or back output tray of the MFC, never touch the shaded parts shown in the following diagram. HOT! HOT! Front view Back view Clear the jammed paper as follows. If the jammed paper is removed completely by using the information in the following steps, you can install the paper tray first, and then close the front cover and the MFC will resume printing automatically. ¦ If a paper jam occurs when using the optional lower tray unit, check for correct installation of the upper paper tray. ¦ Always remove all paper from the paper tray and straighten the stack when you add new paper. This helps prevent multiple sheets of paper from feeding through the MFC at one time and reduces paper jams. TROUBLESHOOTING AND ROUTINE MAINTENANCE 12 - 6 12 - 7 TROUBLESHOOTING AND ROUTINE MAINTENANCE 1 Pull the paper tray completely out of the MFC. 2 Pull the jammed paper up and out of the MFC. 3 Press the cover release button and then open the front cover. 4 Pull out the drum unit assembly. Pull the jammed paper up and out of the MFC. If you cannot remove the drum unit assembly easily at this time, do not use extra force. Instead, pull the edge of the jammed paper from the paper tray. If the jammed paper can not be pulled out easily, turn the jam dial towards you so that you gently pull the paper out. Jam Dial G To prevent damage to the MFC caused by static electricity, do not touch the electrodes shown in the following diagram. 5 Open the back output tray. Pull the jammed paper out of the fuser unit. If the paper jam can be cleared, go to Step 7. If you have to pull the paper toward the back of the MFC, the fuser may get dirty with toner powder and it may scatter on the next printouts. Print a few copies of the test page until the scattering of toner stops. TROUBLESHOOTING AND ROUTINE MAINTENANCE 12 - 8 G After you have just used the MFC, some internal parts of the MFC are extremely HOT! Wait for the MFC to cool down before you touch the internal parts of the MFC. HOT! Back view 6 Open the jam clear cover (fuser cover). Pull the jammed paper out...

Эта инструкция также подходит к моделям:
Факсы - MFC-8840D (3.21 mb)
Факсы - MFC-8640D (3.21 mb)
Факсы - MFC-8440 (3.21 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории