Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Confirm both latches are locked. 11 ^Operating Instructions Loading Copy Paper It is possible to load up to 40 sheets of Letter size copy paper (assuming a paper weight of 80 g/m2). Note that only Letter size paper may be used. When the unit is first used or when UP ” flashes on the Multi-Copy/Error Indicator to indicate that the unit is out of paper, load copy paper as described below. Follow the guidelines below to ensure smooth and accurate printing by the unit. • Only use Letter size copy paper having a weight of 60 to 90 g/m2 as the copy paper for this unit. • Do not simultaneously load paper of varying type and thickness as this may result in paper jams. • Before adding copy paper, be sure to remove all the copy paper remaining inside the unit’s paper cover. (Note that copy paper will slightly resist being removed, but may be pulled out without problems.) After removing the copy paper, stack the removed paper together with the new paper, fan it thoroughly, square it and reload. DO NOT USE THE FOLLOWING TYPES OF PAPER • Extremely smooth or glossy paper • Coated paper • Thermal paper • Paper that is printed on one side • Wrinkled paper, creased paper, etc. V 1 Set the power switch to on ( I ). • “ P ” will flash on the Multi-Copy/Error Indicator when copy paper has run out. 2 Pull the paper cover forward as shown in the left figure. 12 Loading Copy Paper 3 To prevent paper jams such as those caused by multiple sheets feeding at once, fan the paper thoroughly, square it, align it with the guide inside, and insert as far as it will go. (22^3 • Only use Letter size copying paper having a weight of 60 to 90 g/m2 as the copy paper for this unit. • Do not stack more copy paper in the unit than the maximum paper limit indicated by the guide (see figure to the left) as this may result in paper jams. (Note that the unit can hold about 40 sheets of paper having a weight of 80 g/m2.) 4 Close the paper cover until a click is heard. • Close the paper cover, or the unit will not work properly. • The paper cover should be closed to make copies properly. Confirm the both latches are locked. 13 Operating Instructions *> Mill V'< ■: ” k Making Copies This section describes how to copy text and illustrations drawn on the screen. Set the power switch to on ( I ). • “ / ” will light on the Multi-Copy/Error Indicator to indicate that the unit is ready to copy. Press the Copy Key Co]. • Text and illustrations on the screen will be copied and copies emerge from the output port. • The output port can hold up to 10 sheets of copy paper. (Note that exceeding the output port’s capacity may result in paper jams.) • For details on making multiple copies, 2-screen copies and so on, see page 15. iJBTTEl • Do not use paper that has been copied on one side by this printer as copy paper in this unit or in any other copiers or printers as this may result in dirty rollers, degradation of printing quality, paper jams, and streaks and smudges on output paper. • Do not write on the output paper from this unit with the printed side down. The ink on the printed side will be copied on the surface underneath the output paper. • Text or images in shades of yellow will not copy. Making Copies ■ Copy types and procedures Copy Type Procedure Copying the front of the screen Press Col- Copying the back of the screen © Press to move the screen to be copied to the front. © Press Col. Making multiple copies (up to 9) © Select the number of copies (1 to 9) by pressing (g) as necessary. ® Press (~B~l. • Press ® to stop copying in mid-operation. Making 2-screen copies • Copying the front and back of the screen on a single sheet of paper Pres s Ü). 2-Screen Copy I ^.1 2J 1 Front 1 Back j Copying chart paper Chai and copy • Wrir up i • Affi> mec 1 paper can be atta copied. (Be sure to ing is finished.) -I r Attach both p* *-sides with -H| tape x> ^ i -ikies, slackness or fold, i copies as dark shado it to the screen with dr lium adhesive. ched to the screen as shown in the figure take the chart off the screen soon after / s in the chart when attached to the screen will show ws. afting tape made by 3M®or other similar tape with 3M® is a registered trademark of 3M Corporation. Replacing the Thermal Transfer Film The unit is capable of producing about 15 more copies when the Contrast/Remaining Film Indicator begins to flash. The unit has run out of thermal transfer film and can no longer make copies when the Multi-Copy/Error Indicator flashes “r”, Separately available replacement film (UG-6001) may be purchased from the dealer where you purchased the unit. Thermal transfer film is replaced as follows. • Only use the designated product (UG-6001 ) from Panasonic as the replacement film. (Note that using another type of replacement film may result in degraded printing quality or damage to the unit.) • Thermal transfer film is disposable. Dispose of used thermal transfer film as “burnable” o...