Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
11322 Notice • After you install the double feed prevention roller, make sure that the shaft is inserted into the tab, and that the shaft will not rotate or move. If the roller is not installed correctly, it may cause double feeding or a paper jam. Operating Manual Replacement Parts and Optional Units Replacement Parts and Optional Units . Insert the protrusion (A) of the double feed prevention roller cover into the hole on the main unit, and then push in the part of the roller cover indicated by B in the direction indicated by the arrow until it clicks into place. 21 Notice • Make sure that the double feed prevention roller cover does not stick up. If the double feed prevention roller cover is closed incompletely, damage or paper jams can occur. 8. Close the ADF door. • Push both sides of the ADF door down slowly until it clicks into place. Operating Manual Replacement Parts and Optional Units Replacement Parts and Optional Units " (ON). 10. Reset the roller replacing counter in User Utility to 0. • Start User Utility, and in the window, click the [Clear Counter] button for "After Replace Roller" to reset the counter to 0. • For details, refer to the User Utility help. Operating Manual Replacement Parts and Optional Units Replacement Parts and Optional Units The imprinter prints on the face of the document before scanning. The printed material will also be scanned. 1. Set the power switch (A) of the scanner to " " (OFF). 12. Open the imprinter door. Operating Manual Replacement Parts and Optional Units Replacement Parts and Optional Units Connect the cable. Notice • Be sure to correctly match the rib with the slot prior to inserting the connector. 4. While keeping the direction of the imprinter as shown in the diagram below, insert the pins (A) on both sides into the guides, and insert the pins (B) on both sides into the guides until they are locked by the springs (C). 11223 Operating Manual Replacement Parts and Optional Units Replacement Parts and Optional Units Close the imprinter door. 6. Set the power switch of the scanner to " " (ON). Note • For details on installing an ink cartridge, refer to "Installing the Ink Cartridge" (page 77). Operating Manual Replacement Parts and Optional Units Replacement Parts and Optional Units Install the ink cartridge in the imprinter. 1. Set the power switch (A) of the scanner to " " (OFF). 12. Remove the protective tape. Operating Manual Replacement Parts and Optional Units Replacement Parts and Optional Units Move the carriage to the ink cartridge exchange position. Notice • Adjust the position following the label on the imprinter. 4. Insert the ink cartridge into the carriage. 5. Lock the ink cartridge adjustment lever (A). 1 Operating Manual Replacement Parts and Optional Units Replacement Parts and Optional Units 1. Set the power switch of the scanner to " " (OFF). 2. Move the carriage to the ink cartridge exchange position. Notice • Adjust the position following the label on the imprinter. 3. Pinch the ink cartridge adjustment lever (A) and lift it. 1 4. Remove the ink cartridge (A). 1 Operating Manual Replacement Parts and Optional Units Replacement Parts and Optional Units Adjusting the imprinter printing position 1. Move the carriage to the desired printing position, and align the indicator (A) with the " " mark (B) . • The " " mark indicates the printing position. Printing is not available in any other position. 21 Printing Position 16.5 mm (0.6 in.) 30.8 mm (1.2 in.) 141 mm (5.6 in.) 121 mm (4.8 in.) 109.3 mm (4.3 in.) 97.5 mm (3.8 in.)97.5 mm (3.8 in.) 83.5 mm (3.3 in.)83.5 mm (3.3 in.) 66.8 mm (2.6 in.)66.8 mm (2.6 in.) 56.5 mm (2.2 in.)56.5 mm (2.2 in.) 45 mm (1.8 in.)45 mm (1.8 in.) 30.8 mm (1.2 in.) 16.5 mm (0.6 in.) Document sizeDocument sizeCenter Printing Printing can be set from the ICP program and the TWAIN and ISIS drivers. For details, refer to the help for ICP or PIE. Operating Manual Appendix Appendix If a problem occurs while the scanner is being used, check the following items and check the scanner status with the User Utility. If the unit still malfunctions, turn it OFF, unplug the power cord and call for service. Symptom Possible Cause Remedy The ready indicator does not The power cord is not plugged in. Insert the power plug firmly. light when the power switch is turned ON. Problem with power supply. Disconnect the scanner from the electric outlet and call for service. The computer does not recognize the scanner. The scanner is not functioning correctly. The scanner is not connected to the Connect the USB cable correctly. computer correctly. Uninstall the software from the computer, and then install the The software is not installed correctly. software again. (Refer to "Installing the Software" in the Installation Manual.) Check the computer whether the USB The USB interface of the computer is interface of your computer is installed not installed correctly. correctly using the device manager’s property. The scanner is connected via USB Do...