Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Pan/Tilt Invert option . Removable foot stands . Micro-stepping motors . Thermal switch . Fan cooled DMX Channel Summary Q-Roll 150 Control Features o . -7 channel DMX Intelligent Barrel Scanner6 . Pan: 180°6 . Barrel Rotation: 360°6 . Mechanical Dimmer/Shutter/Strobe6 . Rotating Gobos 6 - 8 interchangeable rotating gobos 6- 6 metal, 2 glass, 2 Free gobos 6- Gobo Bounce. 6- Gobo wheel spin 6 - in both directions, at variable speeds6 . Color Wheel 6- 11 colors plus open 6 - includes 1 quad and 1 tri-color split 6- Rainbow color spin 6 - in both directions, at variable speeds6 . Gobo rotation control channel6 . Pan speed & reset control channel6 6 Features o . Built in beat activated and automatic programs 6(stand-alone)6 . LED display menu with inver. Pan/Tilt Invert option6 . Removable foot stands6 . Micro-stepping motors6 . Thermal switch 6 . Fan cooled6 CHANNEL FUNCTION 1 Pan 2 Tilt or Barrel Roll 3 Shutter, Strobe, Dimmer 4 Rotating Gobos 5 Colors 6 Gobo rotation 7 Pan/Tilt Speed & Reset with (P7-n) setting Q-Scan 150 & Q-Roll 150 User Manual 4 2005-11-15/13:23 Introduction Product Overview Control Board Enter Choose Up Down .... SEGMENT BUTTONS I/O PANEL OVERVIEW 1 1. Scanner head 2. Projector 3. Base 4. Carrying handles and removable floor stands 5. Fan (bottom rear) 6. LED power indicator 7. LED display 8. [Enter] button 9. [Choose] button 10. [Up] button 11. [Down] button 12. DMX output 13. DMX input 14. Internal microphone 15. AC input IEC 60320 C14 16. Fuse holder 17. Power switch 18. Voltage switch 19. Music Sensitivity Knob 20. Lamp access plate 21. Lamp optimizing 22. Barrel scanner 2 3 4 12 13 20 21 19 17 6 7 8 9 10 11 5 14 15 16 18 4 22 BUTTONS Choose Down Up Toggles menu functions Steps backward through menu functions Steps forward through menu functions I/O PANEL DMX Out & In Power DMX-512 connectors AC input IEC 60320 C14 and fuse holder Enter Confirms selected menu function Q-Scan 150 & Q-Roll 150 User Manual 5 2005-11-15/13:23 STUP E Lamp You will need to install a lamp prior to the initial operation of the fixture. An HTI150 high intensity discharge lamp is included. Warning! When replacing the lamp, please wait 15 minutes after powering down to allow the unit to cool down! Always disconnect from main power prior to lamp replacement. Do not touch the envelope (glass area) of the bulb with bare hands. If this happens, clean the lamp with alcohol and wipe it with a lint free cloth before installation. Lamp Installation 1. Remove screws labeled (S1) and pull out lamp socket plate. 2. If replacing the lamp, remove old lamp first. 3. Holding the new lamp by its base, align the pins on the lamp with the small hole in the socket and insert the lamp squarely until the retaining clips on the lamp socket secure the lamp tightly. 4. Clean the glass/envelope of the bulb with an alcohol wipe or equivalent. 5. Holding the lamp socket plate, insert the tip of the lamp into the fixture with extreme care. Navigate the lamp all the way until it reaches the reflector and the lamp base plate touches the bottom plate of the fixture. 6. Align the screw holes and fasten the screws back onto the lamp socket plate. 7. If you are replacing the lamp, you may want to log the fixture hours in order to track the lamps use. Navigate to the H000 on the menu display to obtain this information. Please note that it is normal for the fixture to have logged a few hours of testing prior to your use. 8. Turn the fixture on and adjust the lamp alignment screws (S2) until the brightest most even area of the beam is in the center of your spot. It may be necessary for you to use a controller in order to command the fixture to display a white beam on a flat surface with no colors. Maximizing the life of your lamp To ensure the longest and most efficient use of the lamp always wait between 10 and 15 minutes before re-applying power after a shutdown. Failure to do so could result in premature aging of the lamp and failure to the electronics that drive it. S1 S2 S1 Q-Scan 150 & Q-Roll 150 User Manual 6 2005-11-15/13:23 Introduction Lamp Alignment How-To Often, after a new installation of a lamp, you will find that there is an uneven field of light or what is referred to as a hot spot. This is due to the most intense point of the lamp source not being positioned optimally within the reflector. S2 There are three lamp alignment screws provided at the base of the projector head. Turning these screws allow you to optimize the projection quality of the spot as well as the overall intensity of the beam. 1. Project a white spot against any flat surface. Preferably the surface should be white or pastel in color. 2. Turning the lamp alignment screws, try to position the hot spot in the center of the beam as best as possible. This could require many attempts on your part. 3. Once the hot spot is in the center of the spot, do your best to turn all screws equally as to affect movement up or down within the reflector. 4. As you move in and out of...
Эта инструкция также подходит к моделям:Сканеры/копиры/мфу - Q-Roll 150 (454.64 kb)