Оценок - , средний балл:
(
)
)
Производитель: Poulan
Размер: 258.72 kb
Название файла: NOUS2009_545177387.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
- -- AirFilterCoverAirFilterButtonAirFilterCoverAirFilterButton Cleaning the air filter: 1. Clean the cover and the area around it to keep debris from falling into the carburetor chamber when the cover is removed. NOTE: Move choke lever to RUN position before opening air filter cover. 2. Open air filter cover by pushing button (see illustration). Remove air filter. NOTE: Do not clean filter in gasoline or other flammable solvent. Doing so can create a fire hazard or produce harmful evaporative emissions. 3. Wash the filter in soap and water. 4. Allow filter to dry. 5. Apply a few drops of oil to the filter; squeeze filter to distribute oil. 6. Replace parts. REPLACE SPARK PLUG Replace spark plug each year to ensure the engine starts easier and runs better. Set spark plug gap at 0.025 inch (0.6 mm). Ignition timing is fixed, nonadjustable. 1. Twist, then pull off spark plug boot. 2. Remove spark plug from cylinder and discard. 3. Replace with Champion RCJ-6Y spark plug and tighten securely with a 3/4 inch (19 mm) socket wrench. 4. Reinstall the spark plug boot. REPLACE FUEL FILTER To replace fuel filter, drain unit by running it dry of fuel, then remove fuel cap/retainer assembly from tank. Pull filter from tank and remove it from the fuel line. Install new fuel filter on fuel line; reinstall parts. FuelLineFuelFilter CHECKMUFFLERMOUNTINGSCREWS Onceeachyear,ensuremufflermountingscrewsaretightenedsecurelytopreventdamage. Muffler Mounting Screw INSPECT MUFFLER AND SPARK ARRESTING SCREEN WARNING: The muffler on this product contains chemicals known to the State of California to cause cancer. As the unit is used, carbon deposits build up on the muffler and spark arresting screen, and must be removed to avoid creating a fire hazard or affecting engine performance. HoodScrewsSparkArrestingScreenMufflerCover Replace the spark arresting screen every 50 hours of operation or if any damage or breaks in the screen are noted. NOTE: Do not attempt to clean the spark arresting screen. 1. Remove 3 screws from muffler cover. Remove muffler cover. 2. Loosen and remove 4 screws from the muffler hood. 3. Remove the muffler hood and spark arresting screen. 4. Install new spark arresting screen. 5. Reinstall muffler hood and 4 screws. Tighten screws securely. 6. Reinstall muffler cover and 3 screws. Tighten securely. NOTE: If any part of the muffler is cracked, broken or damaged, we recommend that the muffler be replaced. CARBURETOR IDLE SPEED ADJUSTMENT The carburetor has been carefully set at the factory. Adjustments may be necessary if you notice any of the following conditions: S Engine will not idle when the throttle is re leased. To adjust idle speed: Allow engine to idle. Adjust speed until engine runs without stalling (idle speed too slow). S Turn idle speed screw clockwise to in crease engine speed if engine stalls or dies. S Turn idle speed screw counterclockwise to decrease engine speed. 10 - AirFilterCoverAirFilterCover Idle Speed Screw If you require further assistance or are unsure about performing this procedure, contact an authorized service dealer or call 1- --800- --554- --6723. STORAGE --11 - WARNING: Perform the following steps after each use: S Allow engine to cool, and secure the unit before storing or transporting. S Store unit and fuel in a well ventilated area where fuel vapors cannot reach sparks or open flames from water heaters, electric motors or switches, furnaces, etc. S Store unit with all guards in place. Position unit so that any sharp object cannot accidentally cause injury. S Store unit and fuel well out of the reach of children. SEASONAL STORAGE Prepare unit for storage at end of season or if it will not be used for 30 days or more. If your unit is to be stored for a period of time: S Clean the entire unit before lengthy stor age. S Store in a clean dry area. S Lightly oil external metal surfaces. FUEL SYSTEM Under FUELING ENGINE in the OPERATION section of this manual, see message labeled IMPORTANT regarding the use of gasohol in your engine. Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Add stabilizer to gasoline in fuel tank or fuel storage container. Follow the mix instructions found on stabilizer container. Run engine at least 5 minutes after adding stabilizer. HELPFUL TIP During storage of your gas/ oil mixture, the oil will separate from the gas. We recommend that you shake the gas can weekly to insure proper blending of the gas and oil. ENGINE S Remove spark plug and pour 1 teaspoon of 40:1, 2-cycle engine oil (air cooled) through the spark plug opening. Slowly pull the starter rope 8 to 10 times to distribute oil. S Replace spark plug with new one of recommended type and heat range. S Clean air filter. S Check entire unit for loose screws, nuts, and bolts. Replace any damaged, broken, or worn parts. S At the beginning of the next season, use only fresh fuel having the proper gasoline to oil ratio. OTHER S Do not store ga...