Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Users who operate power tools on a continual and regular basis must monitor closely their physical condition and the condition of this tool. ASSEMBLY WARNING: Stop engine and be sure the impeller blades have stopped turning before opening the vacuum inlet door or attempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury. Always disconnect the spark plug before performing maintenance or accessing movable parts. WARNING: If you receive your unit assembled, check each step to insure your unit is properly assembled and all fasteners are secure. Follow all safety information in the manual and on the unit. D A standard screwdriver is required for assembly. BLOWER TUBE ASSEMBLY D Align the rib on the blower tube with the groove in the blower outlet; slide the tube into place. NOTE: Tube clamp must be loose enough to allow blower tube to be inserted in blower outlet. Loosen tube clamp by turning knob coun terclockwise. BlowerTubeBlowerOutletRibGrooveDTightenthetubeclampbyturningtheknobclockwise. DToremovethetube,turntheknobcounterclockwisetoloosenclamp; removetube. VACUUMBAGASSEMBLYDOpenthezipperonthevacuumbagandinserttheelbowtube. DPushthesmallendoftheelbowtubethroughthesmallopeninginthebag. SmallOpeningZipperOpeningElbowTubeRib NOTE:Makesureedgeofthesmallopeningisflushagainsttheflaredareaoftheelbowtube,andtheribontheelbowtubeisonthebottom. DClosethezipperonthebag.Makesurethe zipperisclosedcompletely. DRemoveblowertubefromengine. - -- -- 4 -- Rib Groove D Insert the elbow tube into the blower outlet. Make sure elbow tube rib is aligned with the blower outlet groove. D Turn clamp knob clockwise to tighten. D Secure the ends of the shoulder strap by routing the strap through the buckle as shown. VACUUM TUBE ASSEMBLY WARNING: Stop engine and be sure the impeller blades have stopped turning before opening the vacuum inlet door or attempting to insert or remove the vacuum or blower tubes. The rotating blades can cause serious injury. D Align the lower vacuum tube as shown. Push lower vacuum tube into upper vacuum tube. Lower Vacuum Tube Upper Vacuum Tube D Insert a screwdriver into the latch area on the vacuum inlet cover. Latch Area Blower Outlet Vacuum Inlet Cover Latch Area D Gently tilt the handle of the screwdriver toward the back of the unit while pulling up on the vacuum inlet cover with your other hand. D Hold the vacuum inlet cover open until upper vacuum tube is installed. Vacuum Inlet Vacuum Inlet Cover Retaining Post D Place the hooks on the vacuum tube on the retaining posts; pivot tube into position. Secure vacuum tube by turning the knob clockwise until tight. Hooks Knob D When converting back to the blower feature, make sure latch on the vacuum inlet cover is securely fastened. USING YOUR UNIT WARNING: You MUST make sure the tubes are secure before using the unit. OPERATING POSITION Blower Eye Protection Vacuum OPERATING TIPS S While vacuuming or blowing debris, hold the unit with the muffler side facing away from your body and clothes (see illustration above). S To reduce the risk of hearing loss associated with sound level(s), hearing protection is required. S To reduce the risk of injury associated with contacting rotating parts, stop the engine before installing or removing attachments. Do not operate without guard(s) in place. S Operate power equipment only at reasonable hours--not early in the morning or late at night when peoplemight be disturbed. Comply with times listed in local ordinances. Usual recommendations are 9:00 a.m. to 5:00 p.m., Monday though Saturday. S To reduce noise levels, limit the number of pieces of equipment used at any one time. S To reduce noise levels, operate power blowers at the lowest possible throttle speed to do the job. S Use rakes and brooms to loosen debris before blowing. S In dusty conditions, slightly dampen surfaces or use a mister attachment when water is available. S Conserve water by using power blowers instead of hoses for many lawn and garden applications, including areas such as gutters, screens, patios, grills, porches, and gardens. S Watch out for children, pets, open windows, or freshly washed cars. Blow debris away safely. S Use the full blower nozzle extension so the air stream can work close to the ground. S After using blowers and other equipment, CLEAN UP! Dispose of debris in trash receptacles. FUELING WARNING: Remove fuel cap slowly when refueling. This engine is certified to operate on unleaded gasoline. Before operation, gasoline must be mixed with a good quality 2-cycle air-cooled engine oil. We recommend Poulan or Poulan Pro brand oil. Mix gasoline and oil at a ratio of 40:1 (A 40:1 ratio is obtained by mixing 3.2 ounces of oil with 1 gallon of unleaded gasoline). Do not use automotive oil or boat oil. These oils will cause engine damage. When mixing fuel, follow the instructions printed on the container. Always read and follow safety rules under HANDLE FUEL WITH CAUTION in the safety rules sect...