Оценок - 3, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
• Use care when approaching blind corners, shrubs, trees or other objects that may obscure vision. SLOPE OPERATION Slopes are a major factor related to loss-of-control and tip- over accidents, which can result in severe injury or death. All slopes require extra caution. If you cannot back up the slope, or if you feel uneasy on it, do not drive on it. Do • Blow across the face of slopes; never up and down. • Remove obstacles such as rocks, tree limbs, etc. • Watch for holes, ruts, or bumps. Uneven terrain could overturn the unit. Tall grass can hide obstacles. • Keep all movement on the slopes slow and gradual. Do not make sudden changes in speed or direction. Do Not • Do not start or stop on a slope. If tires lose traction, proceed slowly straight down the slope. • Do not turn on slopes unless necessary, and then, turn slowly and gradually downhill, if possible. • Do not use near drop-offs, ditches, or embankments. The operator could lose footing or balance or blower could suddenly turn over if a wheel is over the edge of a cliff or ditch, or if an edge caves in. • Do not operate on slopes with wet grass. Reduced footing or traction could cause sliding. • Do not use on excessively steep slopes. 3 2 safety rules regarding outdoor power equipment (cont.) CHILDREN Tragic accidents can occur if the operator is not alert to the presence of children. Children are often attracted to the unit and its activity. Never assume that children will remain where you last saw them. • Keep children out of the blowing area and under the watchful care of another responsible adult. • Be alert and turn unit off if children enter the area. • Before and during reverse operation, look behind and down for small children. • Never allow children to operate the unit. • Use extra care when approaching blind corners, shrubs, trees, or other objects that may obscure vision. EMISSIONS • Engine exhaust from this product contains chemicals known, in certain quantities, to cause cancer, birth defects, or other reproductive harm. • Look for the relevant Emissions Durability Period and Air Index information on the engine emissions label. MAINTENANCE AND STORAGE • Always observe safe refueling and fuel handling practices when refueling the unit after transportation or storage. • Always follow the engine manual instructions for storage preparations before storing the unit for both short and long term periods. • Always follow the engine manual instructions for proper start-up procedures when returning the unit to service. • Never store the machine or fuel container inside where there is an open flame, such as in a water heater. Allow unit to cool before storing. • Shut off fuel while storing or transporting. Do not store fuel near flames or drain indoors. • Keep all hardware, especially impeller bolt, tight and keep all parts in good working condition. Replace all worn or damaged decals. • Never tamper with safety devices. Check their proper operation regularly. • Clean leaves and debris from mufflers and engine to prevent fires. Clean up oil or fuel spillage. • Stop and inspect the equipment if you strike an object. Repair, if necessary, before restarting. • Never make adjustments or repairs with the engine running unless specified otherwise. • Park machine on level ground. Never allow untrained personnel to service machine. • Carefully release pressure from components with stored energy. (e.g. springs) • Only replace impellers. Never straighten or weld them. • Keep hands and feet away from moving parts. • Frequently check components and replace with manufacturer’s recommended parts, when necessary. • Use only factory authorized replacement parts when making repairs. • Always comply with factory specifications on all settings and adjustments. • Only authorized service locations should be utilized for major service and repair requirements. • Never attempt to make major repairs on this unit unless you have been properly trained. Improper service procedures can result in hazardous operation, equipment damage and voiding of manufacturer’s warranty. 4 3 unit assembly Note: Please refer to Parts List for correct part identification and placement. FRONT WHEEL ASSEMBLY • Attach left and right caster brackets to caster wheel using 3/8-18 x 2-1/4 bolt and lock nut. Insert bolt through hole in bracket. Place caster wheel onto bolt. Place other caster bracket onto bolt. Secure with lock nut. Do not over tighten. Wheel must rotate freely. • Align caster brackets with the threaded holes located near the discharge on the front of the machine. Note: Angled edge of mounting brackets should be downwards, with holes toward top. Fasten with two 5/1618 x 3/4” hex bolts. Do not tighten. (Note: Fit each bolt with one 5/16 split lock washer and one 5/16 flat washer before installing.) • Check caster wheel for proper vertical alignment (camber), adjust as necessary, then tighten bolts. SIDE AIR DEFLECTOR • Attach side air deflector to top of discharge chute by aligning h...
Эта инструкция также подходит к моделям:Системы вентиляции - LBC6152BV (474.91 kb)