Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
(Figure 9) 2. Pump primer bulb10 X by pushing up on the bulb(D). (Figure 11) 3. Your unit is designed with a 3 position choke: FULL CHOKE “ ”, PARTIAL CHOKE “ ”, and RUN “ ”. Move choke lever to FULL CHOKE “ ” position. (Figure 10)(DO NOT PRESS THROTTLE LOCK OR TRIGGER.) 4. With unit on the ground, hold top of blower-not engine housing cover as it may be hot-step on bottom of frame with foot. (Figure 12) Fig. 9 ACB Fig. 10 123 D Fig. 11 10 STARTING/STOPPING INSTRUCTIONS NOTE: The unit uses the INCREDI-PULL™ starting system with MAX FIRE IGNITION™, which significantly reduces the effort required to start the engine. You must pull the starter rope out far enough to hear the engine attempt to start. There is no need to pull the rope briskly--there is no harsh resistance when pulling. Be aware that this starting method is vastly different from (and much easier than) what you may be used to. 5. Pull starter 4 to 6 times-when unit starts move choke to position 3. If unit fails to start move choke to position 2 and pull 4-6 times until it starts. (Fig.13 & 14 ) 6. Once engine starts move choke to position 3. 7. After unit starts apply 1/4 throttle slightly and slowly then allow engine to warm up for 30 seconds. 8. Pull throttle to run. NOTE: If engine fails to start after repeated attempts, refer to Troubleshooting section. NOTE: Always pull starter rope straight out. Pulling starter at an angle will cause rope to rub against the eyelet. This friction will cause the rope to fray and wear more quickly. Always hold starter handle when rope retracts. Never allow rope to snap back from extended position. This could cause rope to snag or fray and also damage the starter assembly. COLD STARTS (below 55°F) 1. Switch to “RUN (I)” position. 2. Prime 10 times. 3. Choke in position “ ”. 4. Do not press throttle lock or trigger. 5. Pull rope until engine starts should be 1-10 times. 6. Move choke to position “ ”. 7. After unit starts apply 1/4 throttle slightly and slowly then allow engine to warm up for 30 seconds. 8. Press trigger to run. IMPORTANT IDLING INFORMATION In some cases due to operating conditions (altitude, temperature etc.) your blower may need a slight adjustment to the idle speed. After warm up, If unit does not Idle after restarting 2 times, follow these steps to adjust idle. 1. Locate the idle adjustment screw (G) on the carburetor (Figure 15). 2. Using a Phillips or slotted screwdriver - turn screw 1/4 to 1/2 turn clockwise (to the right). Unit should then idle properly. STOPPING THE ENGINE Emergency Stopping Procedure. When it is necessary to stop blower engine immediately, DEPRESS the OFF “STOP ” switch (A) until the engine stops completely (Figure 16). Normal Stopping Method. For normal stopping, release trigger and allow engine to return to idle speed. Then DEPRESS the OFF “STOP ” switch (A) until the engine stops completely. (Figure 16) STARTING A WARM ENGINE (Engine has been stopped for no more than 15-20 minutes). 1. Set throttle latch (see step 2 for starting a cold engine), pull starter rope briskly. 2. If engine does not start, or starts and then stops after 5 rope pulls, follow procedure “STARTING A COLD ENGINE”. Fig. 12 Fig. 13 132 Fig. 14 123 GA Fig. 15 Fig. 16 11 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS BLOWER OPERATIONS 1. Use the blower for trees, shrubs, flower beds, and hard-to-clean areas. 2. Use the unit around buildings and for other normal cleaning procedures. 3. Use the blower around walls, overhangs, fences, and screens. Because of flying debris, always wear American National Standards Institute approved shielded safety glasses or face shield when operating blower. WARNING: Before using your WARNING: blower, review Safety Precautions in your User Manual, and all regulations for operation of the unit. These precautions and regulations are for your protection. DO NOT operate the blower with other people or animals in the immediate vicinity. Allow a minimum of 50 feet (15 meters) between operator and other people or animals. CAUTION: 4. We recommend that a face mask be worn when operating blower in dusty areas. 5. Stand away from the debris, at a distance that will easily allow you to control the direction of blown debris. Never blow debris in direction of bystanders. 6. To control velocity of airstream, blower can be operated at any speed between idle and full throttle. Experience with the unit will help you determine the amount of airflow necessary for each application. 7. Operate power equipment only at reasonable hours--not early in the morning or late at night when people might be disturbed. Comply with times listed in local ordinances. 8. To reduce sound levels, limit the number of pieces of equipment used at any one time. 9. Operate power blowers at the lowest possible throttle speed to do the job. 10. Check your equipment before operation, especially the muffler, air intakes and air filters. 11. Use rakes and brooms to loosen debris before OPERATION INSTRUCTIONS 1. Follow ...