Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
If situations occur which are not covered in this manual, use care and good judgment. If you need assistance, contact your Sears Service Center or call 1-800-235-5878. Failure to follow all Safety Rules and Precautions can result in serious injury. SAVE THESE INSTRUCTIONS CARTON CONTENTS Model 358.748260 • Blower • Blower Tube • 2 Vacuum Tubes • Elbow Tube • Collection Bag Examine parts for damage. Do damaged parts. NOTE: If you need assistance parts missing or damaged, call 1-800-235-5878. ,tDI, WARNING: If received as sembled, ensure your unit is properly assembled and all fasteners are secure. • A standard screwdriver is required for assembly. BLOWER ASSEMBLY not use NOTE: Assembly instructions for using your unit as a vacuum follow this secor find tion. Attaching the blower tube If you have already assembled your unit for use as a vacuum, refer to the _L, WARNING: Stop the unit and section HOW TO CONVERT UNiT FROM disconnect from the power source be- VACUUM USE TO BLOWER USE. fore opening the inlet cover or attempt- To attach blower tube: ing to insert or remove the inlet restrictor, 1. Align the grooves on the blower blower tube, or vacuum tubes. The mo tube with the grooves on the blower tor must be stopped and the impeller outlet. blades no longer turning to avoid serious injury from the rotating blades. 2. Pushthebloweronto tubethe bloweruntilinto outletitsnaps place(tubebyredtube issecured release button). 3. Toremovetube,the theblowerpress tubereleasewhileon buttonpulling tube. {/_Tube Release Button \('_'_, b,// Blower Tube _w_ er outlet VACUUM ASSEMBLY NOTE: Assembly instructions for using your unit as a blower are explained in the previous section. If you have already assembled your unit for use as a blower, remove the blower tube. CAUTION: To avoid causing damage to the unit, DO NOT attempt to use the variable speed control during vacuum use. Remove the inlet restrietor An inlet restrictor is used when using your unit as a blower. This restrictor is not used during vacuum use and must be removed during assembly for vacu um use. NOTE: Be sure to keep the inlet restrictor for using your unit as a blower. 1. Ensure unit is stopped and extension cord is unplugged. 2. Open the inlet cover by inserting the tip of a screwdriver into the latch area on the blower unit. Gently tilt handle of screwdriver toward the front of the unit to release the latch while pulling up on the vacuum inlet cover with your other hand. Bottom view _ Latch Area Vacuum Inlet Cover (closed) Impelle Latch Area Vacuum' nlet Cover (opened) 3. Turn the inlet restrictor counterclockwise and remove it from the unit. Do not close the inlet door. You will next attach the vacuum tubes. Vacuum } Inlet Restdctor Attaching the vacuum tubes There are 2 vacuum tubes, an upper tube and a lower tube. The upper tube has a vacuum assist handle attached to one end and is cut straight on both ends. The upper tube attaches to the blower unit. The lower tube has an angled end that you point toward the ground during vacuum use. The lower tube attaches to the upper tube. 1. Ensure unit is stopped and extension cord is unplugged. 2. While holding inlet cover open, place the hooks of the vacuum assist handle on the retaining posts of the unit. 3. Raise the tube until it is secured to the blower unit by the red inlet cover latch. _k vUarmV,_cuiu PuPetHTUn°cte !_._ Retaining Post 4. To attach the lower vacuum tube to the upper vacuum tube, first align the arrows on the two tubes. Then, press the two tubes together until the lower tube is securely seated in the upper tube (about 3 inches). z_._4 Upper Tube Lower Tube it arrowsuppe oe d,owertubes COLLECTION BAG ASSEMBLY 1. Open the zipper on the collection bag and insert the elbow tube. 2. Push the small end of the elbow tube through the small opening in the bag. NOTE: Make sure edge of the small opening is flush against the flared area of the elbow tube and the hole for the tube release button is on top. 6 HOW TO CONVERT UNIT FROM Elbow Tube Tube ReleaseVACUUM USE TO BLOWER USE Button 1. Stop unit and unplug the extension Hole cord. 2. Remove the vacuum tubes by inserting the tip of a screwdriver into the latch area on the vacuum assist han- Zipper _1 dle. Gently tilt handle of screwdriver toward the front of the unit to release the latch while pulling up on the vac- Opening Opening 3. Close the zipper on the bag. Make uum assist handle with your other sure the zipper is closed complete-hand. ly. Latch Area tube with the grooves on the blower outlet. 4. Align the grooves on the elbow 5. Push the elbow tube onto the blower outlet until it snaps into place (elbow tube is secured by red tube release button). ADJUSTING THE SHOULDER STRAP ON THE COLLECTION BAG 1. Carefully loop the shoulder strap 3. Install the inlet restrictor that was through the buckle as shown in the illustration below. removed when assembling for vac uum use. NOTE: If you are unable to locate the inlet restrictor, the unit will still ope...
Эта инструкция также подходит к моделям:Системы вентиляции - 74826 (1.02 mb)