Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Once you have blown the debris into a pile, you can convert to vacuum mode to collect the debris for disposal. • BLOWER AIR SPEED CONTROL Your Blower Vac has a variable air speed feature that allows you to select the air speed that best fits your needs. To adjust the air speed, simply slide the orange collar. This will allow movement over the full range of 1 3/4"(44.5mm).With the slide collar in the "A" position, as shown in Figure 6, the maximum blower speed will be 200 mph (320 kph). When pushed forward to position "C" ( as far from the tool housing as possible; about 1 3/4"{44.5mm}) the speed will be approximately 140 mph (225 kph). Position "B" (midway between the two) permits infinite adjustment between positions "A" and "C". A little practice will help you determine what is the best speed for your application. USE AS A VACUUM CLEANER: ALWAYS WEAR SAFETY GLASSES. WEAR A FILTER MASK IF THE OPERATION IS DUSTY. USE OF RUBBER GLOVES AND SUBSTANTIAL FOOTWEAR IS RECOMMENDED WHEN WORKING OUTDOORS. FOR HOUSEHOLD USE ONLY. • REMOVING THE BLOWER TUBE ASSEMBLY Switch off the unit and unplug from the outlet. To disconnect the blower tube assembly from the tool, depress the release button, shown in Figure 1, ensuring that the tube does not fall to the ground. NOTE: The release button will not depress if the ON/OFF switch is in the forward (ON) position. • VACUUMING MODE Ensure that the unit is switched off and disconnected from the power supply. Position the vacuum tube and extension tube as shown in Figure 7. Push the extension tube into the vacuum tube until it snaps into place and the arrows shown in Figure 7A are covered as in Figure 7B. If necessary, this can be made easier by wiping the end of the extension tube with a cloth dampened with soapy water only. Attach the vacuum tube assembly (The assembly includes the extension tube, the vacuum tube and the fan chamber.) to the front of the tool. Insert point "A", shown in Figure 8, into the matching recess in the front of the tool point "B", also shown in Figure 8, and swing the tube up to engage the lock, as shown in Figure 9. Attach the collection bag to the vacuum outlet using the bayonet fitting, as shown in Figure 10. Hold the vacuum as shown in Figure 11. Tilt the vacuum tube slightly and use a sweeping action similar to the action described under Blower Mode. The light debris will flow into and through the vacuum tube into the collection bag. Things such as leaves and small twigs will be mulched as they pass through the fan chamber so that the collection bag will hold a lot of debris. When the collection bag gets full, suction will noticeably decrease. Turn off and unplug the tool and unzip the bag to empty before continuing to operate. CAUTION: NEVER UNZIP THE COLLECTION BAG WITHOUT FIRST TURNING OFF AND UNPLUGGING THE VACUUM. NOTE: If the suction decreases and the bag is not full, the vacuum tube is probably clogged with debris. Turn off and unplug the vacuum and clear the tube before continuing. MAINTENANCE • CLEANING AND STORAGE TURN OFF AND UNPLUG TOOL! (Unplug extension cord at power source.) Use only mild soap and a damp cloth to clean the tool. Clean out any clippings which may have accumulated in the Blower/Vac. When used properly with dry leaves the fan chamber of your Blower/Vac should remain clean. If damp earth and debris are ingested some of the particles may build up on the inside of the fan chamber. If this happens the performance of the unit will decrease. This area can be cleaned out by gently wiping out with a damp rag after disconnecting from the power source. Your Blower/Vac should be stored in a dry place. CAUTION: DO NOT POUR OR SPRAY WATER ON THE TOOL IN AN ATTEMPT TO CLEAN. Do not store the tool on or adjacent to fertilizers or chemicals. Such storage can cause rapid corrosion of the metal parts. Use only mild soap and a damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. ACCESSORIES Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call: 1-800-54-HOW-TO (544-6986). WARNING: The use of any accessory not recommended for use with this tool could be hazardous. Leaf Collection System Cat. No. BV-006 (Available from your dealer at extra cost.) (BV-006 is included with BV9000). The Leaf Collection System replaces the collection bag with a system of collecting debris directly into a 30-33 gallon trash can. Complete directions for the system’s use are included. (Trash can not included.) IMPORTANT To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (including brush inspection and replacement) should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts. SERVICE INFORMATION Black & Decker offers a full network of company-owned and authorized service locations t...