Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
BEFORE OPERATING • SECURING POWER SUPPLY CORD - Secure the extension cord in the tool's built-in cord retainer as shown in Figure 7 or secure the power supply cord and a suitable extension cord as shown in Figure 8. SWITCH NOTE: The switch will not operate if the release button, shown in Figure 1, is depressed. To turn the tool ON, slide the switch forward, as shown in Figure 1. To turn tool OFF, slide switch to the rear. OPERATION USE AS A BLOWER: ALWAYS WEAR SAFETY GLASSES, WEAR A FILTER MASK IF THE OPERATION IS DUSTY. USE OF RUBBER GLOVES AND SUBSTANTIAL FOOTWEAR IS RECOMMENDED WHEN WORKING OUTDOORS. FOR HOUSEHOLD USE ONLY. • BLOWER MODE Ensure that the unit is switched OFF and is disconnected from the power supply. Assemble blow tube as shown in Figure 2. (This only needs to be done the first time you assemble the unit.) WARNING: When turning the tool off for tube installation or any other reason, wait 10 seconds for the fan to stop rotating before disassembly. Attach the blower tube assembly (The assembly includes the blower tubes, the fan chamber and the blower air speed control mechanism) to the front of the tool, as shown in Figure 3 by inserting point A into the matching recess marked point B, also shown in Figure 3. Swing the tube up to engage the lock, as shown in Figure 4. NOTE: The lock will not engage if the ON/OFF switch is in the forward (ON) position. Hold the end of the blower tube approximately 7 inches (180mm) above the ground and turn the tool ON. Using a sweeping motion, from side to side, advance slowly keeping the accumulated debris (leaves,grass clippings etc.) in front of you, as shown in Figure 5. • BLOWER AIR SPEED CONTROL Your Blower has a variable air speed feature that allows you to select the air speed that best fits your needs. To adjust the air speed, simply slide the collar. This will allow movement over the full range of 1 3/4 in.(44.5mm).With the slide collar in the "A" position, as shown in Figure 6, the maximum blower speed will be 200 mph (320 kph). When pushed forward to position "C" ( as far from the tool housing as possible; about 1 3/4 in.{44.5mm}) the speed will be approximately 140 mph (225 kph). Position "B" (midway between the two) permits infinite adjustment between positions "A" and "C". A little practice will help you determine what is the best speed for your application. • REMOVING THE BLOWER TUBE ASSEMBLY Switch off the unit and unplug from the outlet. To disconnect the blower tube assembly from the tool, depress the release button, shown in Figure 1, ensuring that the tube does not fall to the ground. NOTE: The release button will not depress if the ON/OFF switch is in the forward (ON) position. TROUBLESHOOTING Problem Possible Cause Possible Solution • Unit will not start. • Cord not plugged in. • Plug tool into a working outlet. • Circuit fuse is blown. • Replace circuit fuse. (If the product repeatedly causes the circuit fuse to blow, discontinue use immediately and have it serviced at a Black & Decker service center or authorized servicer.) • Circuit breaker is tripped. • Reset circuit breaker. (If the product repeatedly causes the circuit breaker to trip, discontinue use immediately and have it serviced at a Black & Decker service center or authorized servicer.) • Cord or switch is • Have cord or switch replaced at Black damaged. & Decker Service Center or Authorized Servicer For assistance with your product, visit our website for the location of the service center nearest you or call the BLACK & DECKER help line at 1-800-544-6986. MAINTENANCE • CLEANING AND STORAGE TURN OFF AND UNPLUG TOOL! (Unplug extension cord at power source.) CAUTION: DO NOT POUR OR SPRAY WATER ON THE TOOL IN AN ATTEMPT TO CLEAN. Do not store the tool on or adjacent to fertilizers or chemicals. Such storage can cause rapid corrosion of the metal parts. Use only mild soap and a damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts. ACCESSORIES Recommended accessories for use with your tool are available from your local dealer or authorized service center. If you need assistance regarding accessories, please call: 1-800-544-6986). WARNING: The use of any accessory not recommended for use with this tool could be hazardous. SERVICE INFORMATION All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow page directory under "Tools—Electric" or call: 1800- 544-6986 or visit FULL TWO-YEAR HOME...
Эта инструкция также подходит к моделям:Системы вентиляции - BL1200 (345.8 kb)