Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
1. With the unit off and unplugged, install the blower tube onto the motor housing. Turn the tube clockwise until it locks (Figs. 1, 2 and 3). ASSEMBLY PARTS BLOWER MODEL-180r ASSEMBLY PARTS BLOWER MODEL-190r BLOWER TUBE REAR HAND GRIP MOTOR HOUSING BLOWER NOZZLE TUBE MOTOR HOUSING 2. Insert the blower nozzle or concentrator tube onto the blower tube and turn it clockwise to lock (Figs. 2, 3 and 4). ASSEMBLY INSTRUCTIONS 2. Align the arrow on the upper vacuum tube with the arrow on the motor housing (Fig. 7). Note that the flat on the upper vacuum tube faces the vacuum door as you install the tube. Fig. 7 UPPER VACUUM TUBE FLAT MOTOR HOUSING 3. Slide the upper vacuum tube into the motor housing. Turn the tube clockwise until the dot on the tube aligns with the dot on the motor housing (Fig. 8). UPPER VACUUM TUBE MOTOR HOUSING Fig. 8 4. Slide the lower vacuum tube into the upper vacuum tube. The arrow on the lower vacuum tube should align with the arrow on the upper vacuum tube (Fig. 9). 5. Turn the tube clockwise until the dot on the lower vacuum tube aligns with the dot on the upper vacuum tube (Fig. 9). Fig. 9 LOWER VACUUM TUBE UPPER VACUUM TUBE NOTE: For electric vacuum kits, the shorter end of the vacuum bag elbow tube with the raised ribs should be inserted through the zipper opening (Fig. 10). 6. Open the zipper on the large end of the vacuum bag. 7. Insert the vacuum elbow tube through the zipper opening in the vacuum bag (Fig. 10), then through the bag opening in the other end of the bag, until the bag tube opening is seated against the tube flange. ASSEMBLY - VACUUM BAG VACUUM BAG VACUUM ELBOW TUBE ZIPPER OPENING TUBE FLANGE RAISED RIBS BAG TUBE OPENING INSERT THIS END THROUGH THE BAG TUBE OPENING CURVED END POINTING UPWARD Fig. 10 ASSEMBLY INSTRUCTIONS Fig. 11 8. Close the zipper on the bag (Fig. 11). 9. Align the vacuum bag/elbow tube assembly with the grooves on the motor housing (Figs. 12 and 13). 10. Install the vacuum bag/elbow tube assembly onto the motor housing. Turn the assembly clockwise until it locks (Fig. 12). WARNING: Vacuum bag assembly must be used at all times during vacuum mode to prevent personal injury from objects being discharged from blower outlet and to prevent overheating of motor. Fig. 12 ASSEMBLY - AS A VACUUM VACUUM BAG NOTE: Make sure the angled end of the vacuum tube is facing the bag. VACUUM ELBOW TUBE LOWER VACUUM TUBE UPPER VACUUM TUBE MOTOR HOUSING ASSEMBLY PARTS FOR VACUUM MODE VACUUM BAG LOWER VACUUM TUBE UPPER VACUUM TUBE VACUUM DOOR VACUUM ELBOW TUBE MOTOR HOUSING Fig. 13 OPERATING INSTRUCTIONS 1. Use an appropriate extension cord to connect to power. See Electrical Safety Warnings for recommended cords. WARNING: To reduce the risk of electric shock, this unit has a polarized plug (one blade is wider than the other). The outdoor extension cord used with the unit must also be polarized. The plug on the extension cord will fit into the unit only one way. If the plug doesn’t fit fully into the unit, reverse the plug. If it does not fit, use a cord with a correct connection. If the cord does not fit into the power supply outlet, contact a qualified electrician to install the proper outlet. DO NOT change the plug on the extension cord or unit in any way. 2. Secure the extension cord to motor housing as shown (Fig. 14). Fig. 14 STARTING AND STOPPING THE BLOWER/VAC This unit is equipped with an OFF/LOW/HIGH switch (Fig. 15). For low speed operation, slide the switch up to the first click (A). To select high speed, slide the switch up to the second click (B). To turn the unit off, slide the switch all the way down (C). Fig. 15 (C) (A) (B) WARNING: To avoid serious personal injury, wear goggles or safety glasses at all times when operating this unit. Wear a face mask or dust mask in dusty locations. OPERATING AS A BLOWER Hold the blower as shown in Figs. 16, 17, or 18 and sweep from side to side with the nozzle several inches above the ground or floor. Slowly advance, keeping the accumulated pile of debris in front of you. Most dry blowing operations are better suited to low speed than high. Of course, you may choose to use either and you’ll probably find the high speed better for moving heavier items like large debris or gravel. 1. Use the blower for trees, shrubs, flower beds and hard-to-clean areas (Fig. 16). Fig. 16 2. Use the blower around buildings and for other normal cleaning (Fig. 17). Fig. 17 OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS 3. Use the blower for walls, overhangs and screens (Fig. 18). Fig. 18 OPERATING AS A VACUUM WARNING: To avoid serious personal injury, wear goggles or safety glasses at all times when operating this unit. Wear a face mask or dust mask in dusty locations. WARNING: Turn off and unplug the unit before opening vacuum door or installing or removing vacuum bag to avoid personal injury from the impeller. SHOULDER STRAP ADJUSTMENTS 1. With the unit turned off, hold the unit in your left hand in an upright position. Support the lower ...
Эта инструкция также подходит к моделям:Системы вентиляции - 170r (497.55 kb)