Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Your BILLY GOAT ® FORCE Blower was shipped in one carton, completely assembled except for the Upper Handle Assembly and Front Diverter. Mounting hardware for the Upper Handle Assembly can be found in the parts bag. READ all safety instructions before assembling unit. TAKE CAUTION when removing the unit from the box the Handle Assembly is attached to the unit by cables. PUT OIL IN ENGINE BEFORE STARTING PARTS BAG & LITERATURE ASSY Warranty card P/N-400972, Owner’s Manual P/N-440021, Declaration of Conformity P/N-440022, Handle Hardware-Items #10, #11, and #36 Boxing Parts Checklist Front Air Diverter Item#38 P/N-440045 Handle Upper Assembly Item #30 P/N-440035 Parts Bag & Literature Assy P/N-440020 Honda 9 or 13 hp Subaru 9 hp Part No 440021 Form No F101706A 8 FORCE BLOWER Owner’s Manual ASSEMBLY 1.Follow the steps in figures A and B, then securely tighten all hardware shown. 2.Connect spark plug wire. Figure A Figure B The hardware for attaching the upper handle to the lower is in the parts bag. Install upper handle (item 30), to preassembled lower handle (item 28) by sliding the upper over and down the outside of the lower handle. Using bolt (item #36), washers (item #10) & lock nut (item #11) to install upper handle to lower handle. Finish installing the other side of the upper handle assembly using screw and lock nut provided. The throttle control will be attached to the throttle arm on the engine and wrapped around the engine for shipping. Unwrap and secure throttle control (item #31) to upper handle with screws (item #39). Screws will already be mounted in handle, simply remove and use to mount the throttle control. Two .” open ended wrenches One 3/8 open ended wrench Part No 440021 Form No F101706A 9 FORCE BLOWER Owner’s Manual OPERATION Like all mechanical tools, reasonable care must be used when operating machine. Inspect machine work area and machine before operating. Make sure that all operators of this equipment are trained in general machine use and safety. PUT OIL IN ENGINE BEFORE STARTING STARTING ENGINE: See engine manufacturer’s instructions for type and amount of oil and gasoline used. Engine must be level when checking and filling oil and gasoline. FUEL VALVE: Move fuel valve to "ON" position (when provided on engine). STOP SWITCH: Located on the engine. "ON" position. CHOKE: Operated with choke lever on side of engine. THROTTLE: Controlled by throttle lever on the handle. Move remote throttle control to fast position. Pull starting rope to start engine. ENGINE SPEED: Under normal conditions, operate at minimum throttle to accomplish your current cleaning task. IF YOUR UNIT FAILS TO START: See Troubleshooting on page 13. HANDLING & TRANSPORTING: Using two people to lift machine is recommended. Lift holding the handle and handle brace. Secure in place during transportation. See F900 and F1300 series specifications on page 3 for unit weight. Do not use the front grill as an anchor point when securing the unit for transport. Never lift the machine while the engine is running. BLOWING OPERATION Your Billy Goat Force blower is equipped with an air director cone to allow the operator to direct the air stream up or down as required to assist in moving debris. This feature is extremely useful when debris has piled up to the point that it cannot be blown any farther. The air stream can be directed upward to blow the top of the debris pile over and allow the operator to continue moving more debris farther. Part No 440021 Form No F101706A 10 FORCE BLOWER Owner’s Manual ADJUSTING AIR DIRECTOR To adjust air direction, first loosen knob and then position air director cone to desired angle. When the cone is at a suitable position tighten knob to secure. DO NOT position director cone to where it will blow debris towards people, vehicles or other objects in vicinity. Flying debris may damage, harm, or cause injury to people or objects in air flow range. Adjustment knob FRONT DIVERTER POSITIONING The removable front diverter adapter can be slipped on to direct the air stream forward. First turn off engine, and then simply slide diverter onto cone following guide points and twist till locked in position. This option is extremely useful for cleaning out long cracks in pavement or for cleaning under bushes, building overhangs or along curbs. WARNING: Unit will be hard to handle and be pushed backward by the force of the air pushing against the unit. Keep hands on the unit at all times when using the front diverter. To reduce resistance when attaching the diverter, use a silicone lubricant spray on the locking grooves. This should allow the diverter to slide into position with more ease. Front diverter Part No 440021 Form No F101706A 11 FORCE BLOWER Owner’s Manual MAINTENANCE PERIODIC MAINTENANCE Periodic maintenance should be performed at the following intervals: Maintenance Operation Every Use Daily or Every 5 Hours Every 25 Hours Every 50 Hours Every 100-150 Hours Inspect for worn or damaged parts. . Check f...
Эта инструкция также подходит к моделям:Системы вентиляции - P / N 440140 (1.28 mb)