Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
• These can be selected by moving the mode indicator to adjust the nozzle position for blow, vacuum or jet vacuum mode. • In vacuum and jet vacuum modes the product will shred leaves etc. BLOW Position 1 - Blow Mode The Gardenvac will blow debris from patios, paths, driveways, lawns, bushes, borders etc. Using As A Blower 1. Select position 1 on the mode indicator. See fig L. 2. Point nozzle towards the ground. 3. To start squeeze trigger. 4. Stand back from debris to be cleared. 5. Point nozzle towards the debris and slowly approach. 6. To stop release trigger. VACUUM Position 2 - Vacuum Mode M In this position your product will pick up leaves, paper, rubbish, cans etc. IMPORTANT: REMOVE NYLON LINE BEFORE VACUUMING CANS Using As A Vacuum 1. Select position 2 on the mode indicator. See fig M. 2. Position nozzle slightly above the debris, squeeze the trigger and move slowly back and forth. 3. Do not force the nozzle into the debris as this will impair performance. 4. To stop release the trigger. JET VACUUM N P . Position 3 - Jet Vacuum Mode This position is intended to be used to collect debris which is damp or stubborn. It directs a small jet of air towards the ground which will loosen stubborn material. Using As A Jet Vacuum 1. Select position 3 on the mode indicator. See fig N. 2. Position the nozzle above and slightly forward of the debris and squeeze the trigger. 3. Slowly move the nozzle back over the debris. This allows a jet of air to lift the debris from the ground. 4. To stop release the trigger. Emptying your Gardenvac • Switch off and disconnect from the mains electricity supply BEFORE REMOVING OR REPLACING the fully assembled debris bag. Emptying Your Gardenvac 1. Remove debris bag as described on page 4. 2. Empty debris bag holding the moulded handle at the top of the bag and the fabric handle at the bottom of the bag. (P) DO NOT PLACE HANDS IN BAG WHEN EMPTYING, . . SHARP DEBRIS CAN CAUSE INJURY 3. Flip the debris fin back into place before re-fitting as described on page 3. 6 WARNING Never use water for cleaning your product, use only a dry cloth. Do not clean with chemicals or solvents, some can destroy critical plastic parts. After Using Your Gardenvac (Q1, 2, 3 & 4) 1. Switch off and disconnect from the mains electricity supply before cleaning your product. 2. Always empty the debris bag. 3. Take extra care to clean around the cutting head and the collection chute.(Q1) • Take care when cleaning around the cutting line area - sharp edges can cause injury. 4. Inspect the cutting line and replace if worn or damaged 5. Using a soft brush remove debris from all air inlets. (Q2) 6. Remove dirt and debris from debris fin.with a suitable tool. (Q3) 7. Wipe over your product with a soft dry cloth. (Q4) Replacing the Cutting Line (Q5 & 6) • Switch off and disconnect from the mains electricity supply before replacing the cutting line • Handle the cutting line with care - sharp edges can cause injury. 1. Remove debris bag from product. See Page 4. 2. Remove cutting line (Q5) and discard safely. 3. If the cutting line becomes broken during use - use a suitable tool to lever the line out of location. (Q6). 4. Place the cutting line into the slot in the cutting head. Ensure the cutting line is correctly located. See Page 3. 5. Re-fit debris bag to product. See Page 3. Storing Your Gardenvac Always store the product in a dry place ensuring the cable is not likely to be damaged on sharp edges etc. Fault Finding Hints Fails To Operate 1. Is the power turned on? 2. Is the fully assembled debris bag correctly fitted to the product? 3. Check the fuse in the plug, if blown replace. 4. Fuse continues to blow? Immediately disconnect from the mains electricity supply and consult your local Service Centre/Dealer/Distributor Poor Blowing 1. The air inlets are blocked, clean all air inlets. 2. Mode indicator not in the right position? 3. If poor blowing persists? Immediately disconnect from the mains electricity supply and consult your local Service Centre/Dealer/Distributor Poor Vacuum/Jet Vacuum 1. The air inlets are blocked, clean all air inlets. 2. Mode indicator not in the right position? 3. If poor vacuuming persists? Immediately disconnect from the mains electricity supply and consult your local Service Centre/Dealer/Distributor Excessive Vibration 1. The cutting line is damaged - replace with new cutting line. 2. Ensure the fully assembled debris bag is correctly fitted to the product. 3. If excessive vibration persists? Immediately disconnect from the mains electricity supply and consult your local Service Centre/Dealer/Distributor Poor Shredding 1. The cutting line is damaged - replace with new cutting line. 2. TO PROLONG CUTTING LINE LIFE The Gardenvac has been designed to shred leaves. If collecting large amounts of any other debris - remove the cutting line. 3. If poor shredding persists? Immediately disconnect from the mains electricity supply and consult your local Service Centre/Dealer/Distributor Ser...
Эта инструкция также подходит к моделям:Системы вентиляции - 96486380100 (418.78 kb)