Оценок - , средний балл: ( )

Инструкция по эксплуатации Frigidaire, модель DOWNDRAFT SYSTEM PL36DD

Производитель: Frigidaire
Размер: 191.4 kb
Название файла:

Язык инструкции:

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

Документ загружается, подождите пожалуйста

Скачать инструкциюЗакрыть

NOTE: The unit is shipped with the 3-1/4" x 10" discharge facing DOWN. See “CHANGING BLOWER DIRECTION” on page 3, if necessary. EQUALS 6 FT. OF STRAIGHT DUCT 6" ROUND ELBOW 3-1/4" X 10" TO 6" RD. TRANSITION 3-1/4" X 10" 90O ELBOW EQUALS 8 FT. OF STRAIGHT DUCT EQUALS 2 FT. OF STRAIGHT DUCT 3. The system will operate most efficiently when the ductwork does not exceed 40 feet of equivalent duct. The chart, above, shows equivalent feet of elbows and transitions. The number of feet of straight duct plus the equivalent feet of transitions and/or elbows to be used should equal 40 feet or less. NOTE: The equivalent feet of various roof and wall caps hasbeen taken into consideration. Do not include them in this calculation. PLAN THE WIRING 1. The downdraft blower system draws 4 AMPS and requires a 120 VAC, 60 Hz circuit. 2. The unit has a 2 ft. long power cord with a 3-pronged plug. Plan to provide a grounded outlet in a location which will allow the unit’s power cord to reach. (Note: If the Model PL30DD is being installed in a 30" wide cabinet or the Model PL36DD is being installed in a 36" wide cabinet, the outlet cannot be located on the back wall of cabinet.) Outlet may also be wall-mounted, with access hole in cabinet. 2 PREPARATION CHANGING BLOWER DISCHARGE (Optional) The blower is shipped with its discharge facing DOWN. Follow these steps ONLY if: • the position of the blower discharge needs to be moved so ductwork does not interfere with floor joists, plumb ing or wiring below. • it is necessary to rotate the blower discharge to the RIGHT or LEFT. Place the unit on its back on a table or work surface. DOWN DISCHARGE - MOVING BLOWER LEFT OR RIGHT SHEET CLAMP CHANNEL NUTS METAL SCREW BOTTOM FLANGE BLOWER 1.Loosen the 4 nuts and 2 clamp channels. 2.Slide blower to desired position. 3.Use supplied cover plate to close open space (if any). 4.Tighten wing nuts to secure top of blower and use sheet metal screws through bottom flange to secure bottom of blower. LEFT OR RIGHT DISCHARGE COVER PLATE CLAMP CHANNEL NUT BLOWER MOTOR PLUG SHEET METAL SCREW 1. Remove the 4 nuts and 2 clamp channels. CUT COUNTERTOP OPENING 1. Lay out and cut the cooktop cut-out far enough FORWARD so downdraft will fit behind it. 2. Set cooktop in place and slide it as far forward as possible. Center and square it with edges of countertop. 3. Place the plastic template against the back flange of the cooktop and center it. Trace around template to mark the downdraft opening. 4. Remove cooktop from countertop. 5. Cut downdraft opening. Be careful not to chip edges of countertop. MOUNT THE UNIT LEVELING BRACKET - FLANGE FACING IN LEVELING BRACKET - FLANGE FACING OUT MOUNTING SCREWS 1. Set downdraft into opening. Extend leveling brackets to floor of cabinet so downdraft sits straight. (Note: Leveling brackets 2. Carefully lift blower and disconnect motor plug if necessary. Reposition blower and RECONNECT MOTOR PLUG. 3. Use supplied cover plate to close open space (if any). 4. Replace clamp channels and use nuts to secure the blower in its new position. 5. Use sheet metal screws through bottom flange to secure bottom of blower. can be removed and re-attached in other positions. Bottom flange may have to face inward in tight cabinet installations.) 2. Secure the downdraft to the countertop as follows: Hold the downdraft against the back of countertop cut-out and tightening the 2 mounting screws (one on each end of unit) on underside of countertop. Use a wood shim between screw and underside of granite countertops. 3. Screw leveling brackets to bottom of cabinet. Tighten screws holding leveling bracket to unit on each side. 3 INSTALL DUCTWORK CAUTION -BEFORE CUTTING HOLE IN CABINET FOR DUCTWORK: Check for interference with floor joists, wall studs, electrical wiring or plumbing. 6" RD. ELBOW & DUCT- WORK 3-1/4" X 10" TO 6" RD. TRANSITION BLOWER COLLARSCREWS .. 1. Cut hole in cabinet as well as holes in wall or floor as necessary. 2. Mount the roof or wall cap and work back towards the cabinet, attaching all ductwork, elbows and transitions as previously planned. Tape all ductwork connections to make them secure and air tight. 3. Connect ductwork (and transition, if required) to downdraft. If necessary, LOOSEN nuts and screws that hold the blower in place, and slide blower left or right to meet ductwork. Retighten screws and nuts. Note: A 3-1/4" x 10" collar is provided for installers who prefer to rivet the ductwork to the unit. This will allow blower to be removed and replaced easily in service situations without disturbing duct- work. INSTALL ELECTRICAL WIRING 1. Mount a standard wiring box, with 3-pronged receptacle, inside the cabinet. Make sure the downdraft’s power cord can easily reach it. 2. Run appropriate power cable into cabinet and connect it to receptacle. 3. Plug the downdraft’s power cord into the outlet. WIRING DIAGRAM INSTALL COOKTOP 1. Align the cooktop with the downdraft and fasten cooktop in place. Note: Accurate alignment of coo...