Оценок - 4, средний балл: 4.3 ( )

Производитель: Little Wonder Размер: 433.06 kb Название файла: Язык инструкции:

The front discharge position is used to remove debris from along walls, fences, etc. the side discharge position is used to form windrows or piles. The horizontal deflector directs air downward to “chisel” under wet, heavy leaves and litter. The velocity is regulated by the throttle control. Moving the deflector to the upper hole allows for a greater volume of air to be directed downward. Moving the deflector to the lower hole allows for a greater volume of air to be directed upward. To reduce windrowing or to blow over obstacle, point deflector upward. Slight changes in deflector will have a big effect on air flow. Experiment until you find the best position for your needs. For best performance, be sure engine recoil starter assembly, the blower intake and outlet areas are clear and free of leaves or other debris. Maintenance Instructions 1. Keep all nuts, bolts, and screws tight. 2. Never store the Blower with fuel in its fuel tank inside a building or in a confined space where fumes may reach an open flame or sparks. 3. Always refer to the instruction manual for important details if the product is to be stored for an extended period. 4. Engine - 4 cycle. (Refer to engine manufacturer's operating instructions for fuel recommendations and additional information.) 5. Tires - Tubeless. Inflate to air pressure of 30 P.S.I. 6. Labels should be inspected before each use. Replace damaged labels immediately. Check oil level regularly. Be sure correct oil level is maintained. Check oil level after every 5 hours of operation, or daily, before starting engine. Use SAE 30 Oil. Change oil after first 5 hours of operation. Remove drain plug and drain oil while engine is warm. Replace drain plug. Remove oil fill plug and refill with new oil. Start and run engine at idle for 30 seconds. Stop engine. Wait 30 seconds and re-check oil level. If required, add oil to overflowing at oil fill plug. Directions For Fan Removal: (This procedure must be done by qualified Little Wonder dealer) 1. Remove intake guard and front panel. 2. Remove bolt and washer securing fan to engine crankshaft. 3. The fan has a 3/4-16 nut welded on the fan hub. Insert a 3/4-16 grade 5 bolt (or better) and jack or push the fan off the engine. (Little Wonder part #910515 pressure screw is recommended.) In some instances, it may be necessary to apply heat in area of fan hub as Loctite 242 has been used to secure the fan to the engine crank shaft. Be careful not to overheat. 4. Use a new bolt (P/N 910508 or P/N 910518) and Loctite 242 to insure a secure fit upon re-assembling. To prevent accidental starting, remove spark plug wire when servicing engine or equipment. Wire 5. Blower Bolt/Nut Torque Specifications Location Bolt / nut size P/N Min. torque Ft-Lbs (in-lbs) Max. Torque Ft-Lbs (in-lbs) Housing to engine face 5/16-24 x 3/4 flange head 910503 22 (264) 28 (336) Deck to housing 5/16-18 flange nut 114-B 16 (192) 22 (276) Engine to deck 5/16-18 x 1.5/1.75 gr 5 113/942 19 (228) 25 (300) Lower handle to deck 5/16-18 x 1.75 gr 5 942 19 (228) 25 (300) Upper handle to lower handle 5/16-18 x 1.75 gr 5 942 19 (228) 25 (300) Throttle to handle 1/4-20 X 1.5 gr 2 378 4 (48) 6 (72) Interior deflector to hook 10-32 x .625 flange head gr 5 329 (52) (71) Fan to crankshaft ( 9900) 7/16-20 x 1.5 flange head gr 5 910508 61 81 Fan to crankshaft (9100, 9130, 9600, 9810) 3/8-24 x 1.5 flange head gr 5 910518 39 51 Front panel to housing (short stud) 5/16-18 flange nut 114-B 16 (192) 22 (276) Intake guard clamp (long stud) 5/16-18 muloc nut 114-C — 8 (100) Wheel bracket to housing 5/16-18 flange nut 114-B 16 (192) 22 (276) Front wheel axle bolt 3/8-16 x 5.25 gr 5 900501 34 45 Parts Explosions Key # Part # Description Quantity Per Model Number LB800 LB900 1 910648 Intake Guard Label 1 1 2 114C 5/16-18 Nylon Insert Nut 11 11 3 911130 Intake Guard Clamp 3 3 4 921106 Intake Guard Assy 1 1 5 114B 5/16-18 Serrated Flanged Lock Nut 14 14 6 911120 Front Panel 1 1 7 910529 7/16-20 x 1 1/2 Serrated Flange Bolt gd 5 -1 7 600524 3/8-24 x 1 1/2 Serrated Flange Bolt gd 5 1 - 8 910210 8 HP Fan 1 - 8 910220 9 HP Fan -1 9 915 Key 1/4 x 1/4 x 2 1 1 10 910527 Washer hub 6, 8, 10, 13 1 - 10 910528 Washer hub 9 -1 10 6. Key # Part # Description Quantity Per Model Number LB800 LB900 2 114C 5/16-18 Nylon Insert Nut 11 11 5 114B 5/16-18 Serrated Flanged Lock Nut 14 14 14 910915 8 HP IC Intek Engine 1 - 14 930 9 HP Honda Engine -1 15 946 Throttle Clip 1 1 16 910301 Throttle Cable 1 1 17 900301 Upper Handle 1 1 18 900302 Grip (set of 2) 1 1 19 179 1/4-20 x 1 3/4 HHCS gr5 1 1 21 910526 10-32 x 3/4 Self tapping Sheet Metal Screw 1 1 22 972 1/4-20 2-Way Lock Nut 1 1 23 920300 Pneumatic Wheel Offset 2 2 24 312 Retaining Ring 2 2 25 405-1 5/8 SAE Flat Washer 2 2 26 932-1 Axle 1 1 30 916-2 Lower Handle 2 2 31 163 5/16 Flat Washer 12 14 32 920009 8 HP Left Blower Deck 1 - 32 920030 9 HP Right Deck -1 33 920007 8 HP Right Blower Deck 1 - 33 920028 9 HP Left Deck -1 34 942 5/16-18 x 1.75 HHCS gr5 8 8 35 129D...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: