Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
Use only recommended attachments. S Avoid situations which could set the collection bag on fire. Do not vacuum discarded matches, cigars, cigarettes, or ash from fireplaces, barbecue pits, brush piles, etc. To avoid spreading fire, do not use blower near leaf or brush fires, fireplaces, barbecue pits, ashtrays, etc. S Always use the collection bag shoulder strapwhenvacuuming toavoid loss of control. S Check air intake openings, elbow tube, and vacuum tubes frequently, always with the unit stopped and the power source disconnected. Keep vents and tubes free of debris which can accumulate and restrict proper air flow. Do not use with any opening blocked, Keep free of dust, lint, hair and anything that may reduce air flow. CAUTION: To avoid causing damage to the unit, DO NOT attempt to use the variable speed control during vacuum use. STANDARDS This product is listed by Underwriters Laboratories, Inc., in accordance with UL Standard 1017. If situations occur which are not covered in this manual, use care and good judgment. If you need assistance, contact your authorized service dealer or call 1- --800- --554- --6723. Failure to follow all Safety Rules and Precautions can result in serious injury. 4 SAVE THESE INSTRUCTIONS ASSEMBLY WARNING: Stop the unit and disconnect from the power source before opening the inlet cover or attempting to insert or remove the inlet restrictor, blower tube, or vacuum tubes. The motor must be stopped and the impeller blades no longer turning to avoid serious injury from the rotating blades. WARNING: If received assembled, ensure your unit is properly assembled and all fasteners are secure. S A standard screwdriver is required for assembly. BLOWER ASSEMBLY NOTE: Assembly instructions for using your unit as a vacuum follow this section. Attaching the blower tube If you have already assembled your unit for use as a vacuum, refer to the section HOW TO CONVERT UNIT FROM VACUUM USE TO BLOWER USE. To attach blower tube: 1. Align the grooves on the blower tube with the grooves on the blower outlet. 2. Push the blower tube onto the blower outlet until it snaps into place (tube is secured by red tube release button). 3. To remove the blower tube, press the tube release button while pulling on tube. BlowerTubeBloweroutletTubeReleaseButton VACUUM ASSEMBLY NOTE: Assembly instructions for using your unit as a blower are explained in the previous section. If you have already assembled your unit for use as a blower, remove the blower tube. CAUTION: To avoid causing damage to the unit, DO NOT attempt to use the variable speed control during vacuum use. Remove the inlet restrictor An inlet restrictor is used when using your unit as a blower. This restrictor is not used during vacuum use and must be removed during assembly for vacuum use. NOTE: Be sure to keep the inlet restrictor for using your unit as a blower. 1. Ensure unit is stopped and extension cord is unplugged. 2. Open the inlet cover by inserting the tip of a screwdriver into the latch area on the blower unit. Gently tilt handle of screwdriver toward the front of the unit to release the latch while pulling up on the vacuum inlet cover with your other hand. LatchAreaBottomviewofunit Vacuum Inlet Cover (closed) LatchAreaImpeller Vacuum Inlet Cover (opened) 3. Turn the inlet restrictor counterclockwise and remove it from the unit. Do not close the inlet door. You will next attach the vacuum tubes. Vacuum Inlet Cover Inlet Restrictor Attaching the vacuum tubes There are 2 vacuum tubes, an upper tube and a lower tube. The upper tube has a vacuum assist handle attached to one end and is cut straight on both ends. The upper tube attaches to the blower unit. The lower tube has an angled end that you point toward the ground during vacuum use. The lower tube attaches to the upper tube. 1. Ensure unit is stopped and extension cord is unplugged. 2. While holding inlet cover open, place the hooks of the vacuum assist handle on the retaining posts of the unit. 3. Raise the tube until it is secured to the blower unit by the red inlet cover latch. 5 RetainingPostVacuumAssistHandleUpperVacuumTubeHookVacuumAssistHandleUpperVacuumTubeHook 4.Toattachthelowervacuumtubetotheuppervacuumtube,firstalignthearrowsonthetwotubes.Then,pressthetwotubestogetheruntilthelowertubeissecurelyseatedintheuppertube(about3inches). AlignarrowsonupperandlowertubesLowerTubeUpperTube COLLECTION BAG ASSEMBLY 1. Open the zipper on the collection bag and insert the elbow tube. 2. Push the small end of the elbow tube through the small opening in the bag. NOTE: Make sure edge of the small opening is flush against the flared area of the elbow tube and the hole for the tube release button is on top. SmallZipperOpeningElbowTubeTubeReleaseButtonHole Opening 3. Close the zipper on the bag. Make sure the zipper is closed completely. 4. Align the grooves on the elbow tube with the grooves on the blower outlet. 5. Push the elbow tube onto the blower outlet until it snaps into place (elbow tube i...