Оценок - 3, средний балл: 5
(
)
)
|
Фрагмент инструкции
Read the operator's manual for complete safety, assembly, operating and maintenance and repair information. SYMBOL MEANING • SAFETY ALERT SYMBOL Indicates danger, warning, or caution. May be used in conjunction with other symbols or pictographs. •WARNING - READ OPERATOR'S MANUAL Read the Operator’s Manual(s) and follow all warnings and safety instructions. Failure to do so can result in serious injury to the operator and/or bystanders. • WEAR EYE AND HEARING PROTECTION WARNING: The operation of any power tool can be the source of thrown objects and loud noise which can cause severe eye injury and hearing loss. Always wear safety glasses or goggles eye protection meeting ANSI Z87.1 standards and ear protection when operating this unit. Use a full face shield when needed. • KEEP BYSTANDERS AWAY WARNING: Keep all bystanders, especially children and pets, at least 50 feet (15 m) from the operating area. • THROWN OBJECTS CAN CAUSE SEVERE INJURY WARNING: Do not operate unit without proper attachments and guards in place. • BLOWER/VACUUM – ROTATING IMPELLER CAN CAUSE SEVERE INJURY WARNING: Stop the engine/motor before installing or removing tubes and bag, or before cleaning or performing any maintenance. Do not put hands or other objects into fan housing. Keep hands and feet away from rotating impeller. KNOW YOUR UNIT RULES FOR SAFE OPERATION RULES FOR SAFE OPERATION APPLICATIONS With Blower/Vacuum Add-On: • Easily converts from blower to vacuum. Shaft Housing Air intake Vacuum Tube Blower Tube Hanger Shaft Housing Vacuum Bag Strap BLOWER VACUUM •Wide diameter tube for easy debris collection. • Turns debris into mulch. Knob ASSEMBLY INSTRUCTIONS NOTE: Your unit is completely assembled as a blower in the carton. Use the following instructions to convert between a blower and a vacuum. WARNING: To avoid serious personal injury and damage to the unit, shut unit off before removing or installing add-ons. CONVERTING TO A VACUUM 1. Loosen the clamping knob on the blower housing counterclockwise. 2. Remove the blower tube. 3. Install the bag elbow and tighten the knob clockwise (Fig. 1). Fig. 1 Knob Elbow Vacuum Bag 4. Fasten the strap to the shaft above the assist handle, located on the powerhead (Fig. 2). Strap Assist Handle Shaft Fig. 2 CONVERTING TO A BLOWER 1. Remove the vacuum bag. 2. Clip the blower tube to the end of the vacuum tube (Fig. 3). Vacuum Tube Clip Fig. 3 Blower Tube 3. Install the blower tube and tighten the knob (Fig. 4). Knob Blower Tube Fig. 4 OPERATING INSTRUCTIONS ASSEMBLING THE COUPLER The following Troy-Bilt Add-Ons are also available for your unit: Cultivator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TBGC Hedge Trimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . .TBHS Edger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TBLE Straight Shaft Trimmer . . . . . . . . . . . . . . . . . . . . . .TBSS Snow Thrower . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TBST Turbo Blower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TBTB Tree Pruner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .TBTP Removing the add-on WARNING: Read and understand operator’s manual for unit to be used with this add-on prior to operation. 1. Turn the knob counterclockwise to loosen (Fig. 5). 2. Press and hold the release button (Fig. 5). 3. While firmly holding the upper shaft housing, pull the blower/vaccuum add-on out of the coupler (Fig. 6). Installing the add-on WARNING: To avoid serious personal injury and damage to the unit, shut unit off before removing or installing add-ons. 4. Turn the knob clockwise to tighten (Fig. 7). Primary Hole Upper Shaft Housing Coupler Fig. 6 Lower Shaft Housing Release Button Knob CAUTION: Lock the release button in the primary hole (Fig. 6) and securely tighten the knob before operating this unit. Knob NOTE: To make installing or removing the add-on easier, place the unit on the ground or on a work bench. 1. Remove the hanger from the top of the shaft housing. 2. Turn knob counterclockwise to loosen (Fig. 5). 3. While firmly holding the add-on, push it straight into the coupler (Fig. 6). Coupler Release Button Guide Recess ClockwiseCounterclockwise Knob Fig. 5 NOTE: Aligning the release button with the guide recess will help installation (Fig. 5). Fig. 7 CAUTION: The add-ons with the coupler system are to be used in the primary hole only. Using the wrong hole could lead to personal injury or damage to the unit. The blower/vacuum add-on should be installed with the release button in the primary hole. Check Flex Shaft Engagement Prior to Using 1. Start the unit. 2. Briefly engage and release the trigger. 3. Check that add-on is operating. 4. If the add-on is not operating, remove add-on and repeat steps for installing the add-on. 5. Recheck operation of add-on attachment. OPERATING INSTRUCTIONS 9 Fig. 8 Fig. 9 Fig. 10 OPERATING TIPS NOTE: Move the unit slowly back and forth over debris to be vacuumed...
Эта инструкция также подходит к моделям:Системы вентиляции - TBBV (868.37 kb)