Оценок - 2, средний балл: 3.5
(
)
)
|
Фрагмент инструкции
Friction washers maintain throttle lever setting. 8. SHOULDER HARNESS -Used to support unit on operator's back. The straps are adjustable. 9. CHOKE -Move lever UP to close choke ( ) (starting position) and for emergency stopping. Move DOWN to open choke ( ) (run position). 10. PRIMER BULB - Pumping primer bulb before starting engine draws fresh fuel from the fuel tank priming the carburetor for starting. Pump primer bulb until fuel is visible and flows freely in the clear fuel tank return line. Pump bulb an additional 4 or 5 times. 11. LOCKING KNOB -Allows operator to adjust handle position for optimum comfort and control. 12. HANDLE -Used by operator to direct and control air flow. 13. STOP SWITCH -Slide switch mounted on top of handle. Move forward to run, back to stop. 14. THROTTLE TRIGGER -Spring loaded to return to idle when released. During acceleration, press trigger gradually for best operating technique. 15. BLOWER PIPES -Twist lock design. 16. FLEXIBLE PIPE -Allows for full range of movement. POWER BLOWER OPERATOR'S MANUAL POWER BLOWER OPERATOR'S MANUAL MODEL -----------------------------------------------------PB-413H, PB-413T Length -------------------------------------------------------320 mm (12.6 in.) Width--------------------------------------------------------460 mm (18.1 in.) Height -------------------------------------------------------480 mm (18.8 in.) Weight (dry) PB-413H ------------------------------------9.8 kg (21.7 lb.) Weight (dry) PB-413T------------------------------------9.4 kg (20.7 lb.) Engine Type ------------------------------------------------Air cooled, two-stroke, single cylinder gasoline engine Displacement -----------------------------------------------44.0 cc (2.69 cu. in.) Bore ----------------------------------------------------------40.0 mm (1.574 in.) Stroke --------------------------------------------------------35.0 mm (1.378 in.) Carburetor --------------------------------------------------Zama Diaphragm, model C1M w/primer bulb Ignition System --------------------------------------------Flywheel Magneto, capacitor discharge ignition type Spark Plug --------------------------------------------------NGK BPM-8Y Gap 0.65 mm (0.026 in.) Exhaust System --------------------------------------------Spark Arrestor Muffler w/catalyst Fuel ----------------------------------------------------------Mixed (Gasoline and Two-stroke Oil) Fuel/Oil Ratio -----------------------------------------------50:1 ECHO High Performance, two-stroke air cooled engine oil Gasoline -----------------------------------------------------89 Octane unleaded. DO NOT use fuel containing methyl alcohol, more than 10% ethyl alcohol or 15% MTBE. Oil ------------------------------------------------------------50:1 ECHO High Performance, two-stroke air cooled engine oil Fuel Tank Capacity ----------------------------------------1.9 lit. (64.3 US fl. oz.) Recoil Starter System --------------------------------------Automatic Recoil Starter Centrifugal Type Idle Speed---------------------------------------------------2300 - 3200 (RPM) Wide Open Throttle Speed -------------------------------6200 - 8200 (RPM) Maximum Air Speed (Measured at pipe end) ----------282 KM/H (175 mph) Average Air Volume (Measured at pipe end) ----------10.8cu.m/min.(380cu. ft./min.) Sound level at 50 ft. dB(A) scale per ANSI B175.2-----70dB(A) 12 12 PB-413H WARNING DANGER Never perform maintenance or assembly procedures with engine running or serious personal injury may result. INSTALL BLOWER PIPES / STICK HANDLE 1. Assemble clamps (A) onto both ends of flexible pipe (B). 2. Assemble straight pipe with swivel (C) into flexible pipe (B). 3. Assemble flexible pipe (B) to elbow (D) on blower. NOTE C A B A D A light lubricant may be used to ease assembly of flexible pipe to blower elbow. 4. Tighten clamps (A). 5. Loosen wing nut (E) completely and expand stick handle clamp (F). 6. Align notches (G) in handle clamp with pipe pegs (H). Stick handle should be angled away from operator. 7. Slide stick handle onto pipe with swivel (C) 8. Position stick handle for comfortable operation, and tighten wing nut (E). 9. Assemble straight pipe (J) to pipe with swivel (C), turning straight pipe sclockwise to lock in place. 10. Assemble curved pipe (K) to straight pipe (J) turning straight pipe (K) clockwise to lock in place. H G F C E J K C POWER BLOWER OPERATOR'S MANUAL POWER BLOWER OPERATOR'S MANUAL T DANGER WARNING Never perform maintenance or assembly procedures with engine running or serious personal injury may result. INSTALL BLOWER PIPES 1. Assemble clamps (A) onto both ends of flexible pipe (B). 2. Assemble straight pipe with swivel (C) into flexible pipe (B). 3. Position throttle linkage so cable passes between the elbow (G) and frame and runs along the top of the flexible pipe. Remove clamp screw (D) on handle (E). Spread clamp and install onto straight pipe with swivel (C). 4. Assemble flexible pipe (B) to elbow (G) on blower. NOTE A ligh...
Эта инструкция также подходит к моделям:Системы вентиляции - PB-413T (461.52 kb)