Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Фрагмент инструкции
5. TYPE-3 ( Support Intel® Pentium® 4 LGA 775 ) Installation 1. Before pouring liquid coolant into the tank to test the liquid cooling system, please reconfirm all the tubes have been fastened and the tube clips are in the right position. 2. While removing the tubes for disassembly, please make sure to keep all the devices away from any electronic part. 3. Please make sure to take off the sticker on the bottom of the waterblock. Before installation, please make sure to turn off the power and unplug the power cord. 5-1. Take off the sticker and paste on buffer washer. Refer to Step 3-1 5-2. TYPE-3 bracket and M2.5 screws (as Figure 5-2-1). Lock TYPE-3 bracket on the waterblock with M2.5 screws. (as Figure 5-2-3) Figure 3-3-2 Figure 3-3-1 Figure 3-3-3 3-4. Take off the original heat sink on the motherboard ( as Figure 3-4-1 ), and clean the grease. Thread the screws of the back plate through the back of the motherboard and paste it. ( as Figure 3-4-4 ) &( as Figure 3-4-5 ) Figure 7-3-3 Figure 7-3-5 Figure 7-3-4 Figure 7-3-2 7-4.Apply GIGABYTETM grease on the chipset evenly ( as Figure 7-4-1 ). Thread the screws through the holes of TYPE-3 bracket and place waterblock on the chipset. Thread washers through the screws and lock it on TYPE-3 bracket with spring screws. ( as Figure7-4-2 ) & ( as Figure 7-4-3 ) Figure 3-4-1 Figure 5-2-3 Figure 5-2-1 Figure 5-2-2 5-3. Back plate, screws(A) and wrench. Lock the screws on the suitable holes and take off the paper on the back plate. (as Figure 3-3-3) Refer to Step 3-3 Hardware Installation 1. Please take off the heat sink of the chipset on the motherboard. 2. Lock the Waterblock : 4 different types. Figure 3-4-5 Figure 3-4-3 Figure 3-4-4 Figure 3-4-2 5-4. Take off the original heat sink on the motherboard(as Figure 5-4-1), and clean the grease. Thread the screws of the back plate through the back of motherboard and paste it. (as Figure 5-4-3) Figure 7-4-2 Figure 7-4-3 Figure 7-4-1 3-5. Apply GIGABYTETM grease on the chipset evenly (as Figure 3-5-1). Thread the screws through the holes of TYPE-1 bracket and place the waterblock on the chipset. Thread washers through the screws and lock it on TYPE-1 bracket with spring screws. (as Figure3-5-2) & (as Figure 3-5-3) 7-5. Put a 1/4” tube clip into a 1/4” tube (as Figure 3-6-1) and connect the tube with the waterblock and fasten it with tube clip. (as Figure 3-6-6) Refer to Step 3-6 TYPE-1 ( Supports AMD K8 / AM2 ) TYPE-2 ( Supports Intel® Pentium® 4 LGA775 ) 8.Tube Installation Please refer to the figure and the steps below to install GBT Cchipset Waterblock tube. The following is the installation steps for GIGABYTETM 3D Galaxy II. Figure 5-4-2 Figure 5-4-1 Figure 5-4-4 Figure 5-4-3 5-5. Apply GIGABYTETM grease on the chipset evenly ( as Figure 5-5-1 ). Thread the screws through the holes of TYPE-3 bracket and place waterblock on the chipset. Thread washers through the screws and lock it on TYPE-3 bracket with spring screws. ( as Figure5-5-2 ) & ( as Figure 5-5-3 ) TYPE-4 ( Supports Intel® Pentium® 4 LGA775 ) TYPE-3 ( Supports Intel® Pentium® 4 LGA775 ) 4-way splitter valve B Figure 3-5-1 Figure 3-5-2 Figure 3-5-3 3-6. Put a 1/4” tube clip into a 1/4” tube ( as Figure 3-6-1 ) and connect the tube to the waterblock and fasten it with the tube clip. ( as Figure 3-6-2 ) Accessories List Figure 3-6-1 Figure 3-6-2 Figure 5-5-3 Figure 5-5-1 Figure 5-5-2 5-6 Put 1/4” tube clip into 1/4” tube (as Figure 3-6-1) connect the tube to the waterblock and fasten it with tube clip.(as Figure 3-6-4) Refer to Step 3-6 6. TYPE-4 ( Support Intel® Pentium® 4 LGA 775 ) Installation A Figure 3-6-5 Figure 3-6-6 Figure 3-6-4 Figure 3-6-3 (4) Grease x 1 (2) 1/4” Tube Clip x 2 (1) H................Heat Sink x 8 (3) Spring Screws x 4 6-1. Take off the sticker and paste on buffer washer. Refer to Step 3-1 4-way splitter valve 4. TYPE-2 ( Support Intel® Pentium® 4 LGA 775 ) Installation 6-2. TYPE-4 bracket.4 pieces of hook, 4 sets of sping screw, 4 pieces of washer.(as Figure6-2-1) Thread the hook through TYPE-4 bracket, put on the washer and fasten it with spring screws.(as Figure6- 2-2.Figure 6-2-3.Figure 6-2-4) 4-1. Take off the sticker and paste it on the buffer washer. Refer to Step 3-1 8-1. Remove the nylon ties and tube clips from 4-way splitter valve ( A & B ). 4-2. TYPE-2 bracket and M2.5 screws ( as Figure 4-2-1 ). Lock TYPE-2 bracket on the waterblock with M2.5 screws. ( as Figure 4-2-3 ) (7) Washer x 6 (5) Wrench x 1 (6) Hook x 4 (8) M2.5 Screw x 4 Warning : Do not switch on at this point. 8-2. Cut a tube into suitable piece; connect with the first splitter on 4-way splitter valve(A) and connect the other side with the outlet of GBT Cchipset Waterblock and fasten it with tube clip. 8-3. Cut a tube into suitable piece; connect with the first splitter on 4-way splitter valve(B) and connect the other side with the inlet of GBT Cchipset Waterblock and fasten it with tube clip. Figure 6-2-4 Figure 6-2-2 Figure 6-2-1 Figure 6-2-3 6-3. Take off the ...