Оценок - 0, средний балл: 0
(
)
)
|
К этому устройству также есть другие инструкции:
Синтезаторы/фортепиано - S30 (259.23 kb)
Синтезаторы/фортепиано - S30 (956.2 kb)
Синтезаторы/фортепиано - S30 (259.25 kb)
Фрагмент инструкции
Do not remove the other screws. nKeep the removed (6) screws in a safe place. They will be used when attaching the Plug-in board cover to the keyboard again. Appendix 141 Appendix 4 Remove the Plug-in board cover. 8 Mount the Plug-in board onto the plate as detailed in the Plug-in board plate appears. following steps. When installing the optional Plug-in board (from when you remove the cover to when the cover is replaced securely) all operations must be done with the AC power adaptor disconnected. 5Remove the tape holding the Plug-in Board cable to the 8-1 Insert one side of the Plug-in board (the connector side) into the hooks 1 as shown in the illustration. Hook 1 Hook 1 Hooks 1 plate. 8-2 Press down the other side until it is securely 6 Take out the Plug-in board from the anti-static bag. settled on the hooks 2. When installing the board, the side with a connector and Hook 2 ICs must be on top. 7 Carefully plug the cable connector into the Plug-in board connector until the two notches on the cable connector lock into the sockets on the board as shown in the illustration. Hook 2 Hooks 1 Hook 2 Hook 2 Hooks 2 9 Replace the Plug-in board cover by fastening the eight flat-head screws you removed in the step 3 above. Use a coin or a Phillips screwdriver to secure the cover. 142 Removing the Plug-in board from the keyboard 1Press down the hooks 2 in the direction as shown in the illustration and take the board out from the hooks 2 by lifting up the one side. 2Pull out the other side of the board from the hooks 1. 3Pull out the cable connector from the Plug-in board connector. Hook 2 Hook 2 Hooks 2 Removing the Plug-in board from the keyboard 1Press down the hooks 2 in the direction as shown in the illustration and take the board out from the hooks 2 by lifting up the one side. 2Pull out the other side of the board from the hooks 1. 3Pull out the cable connector from the Plug-in board connector. Hook 2 Hook 2 Hooks 2 143 Display Messages Display Messages Message Meaning << ! MIDI buffer full. >> Failed to process the MIDI data because too much data was received at once. << ! MIDI data error. >> Error occurred when receiving MIDI data. << ! MIDI checksum error. >> Error occurred when receiving bulk data. << ! Change internal battery. >> Internal backup battery needs to be replaced. << ! Card full. >> No more available memory on the Memory Card. << ! File not found. >> Can’t find the specified type of file. << ! Bad card. >> Memory Card is faulty. << ! Card not ready. >> Memory Card has not been inserted, or an incompatible card (5V type) has been inserted. << ! Card unformatted. >> Memory Card has not been formatted. << ! Card write protected. >> Memory Card is write protected. << ! Illegal card. >> Memory Card has been wrongly formatted. << ! File already exists. >> File with the same name already exists. << ! Illegal file. >> Data in the file is corrupted and cannot be used. << ! Illegal file name. >> The specified file name is not in MS-DOS format. << ! Read only file. >> File is a read-only type, and cannot be deleted, renamed or saved. << ! Can't make "EXT" file. >> A file could not be created on the Memory Card. << ! Can't make directory. >> No further directories can be created. << ! Too deep directory. >> Directory cannot be entered because it is too deep. << ! Unknown file format. >> File format is not recognized. << ! Bulk protected. >> Bulk data cannot be received because protection is enabled. << ! Device number is off. >> Bulk data cannot be transmitted/received because the device number is set to "off." << ! Device number mismatch. >> Bulk data cannot be transmitted/received because the device numbers don’t match. << ! Effect plugin in slot. >> Cannot be used because Slot contains a Effect Plug-in Board. << ! Plugin communication error. >> Plug-in Board in Slot is not working properly. << ! Plugin type mismatch. >> Sound requires a different Plug-in Board to that inserted in Slot. << ! PLG100 not supported. >> When used with a PLG100 series Plug-in Board, a data file of which File Type is “plugin” cannot be stored on a Memory Card. << Executing... >> Operation is being executed. << Now working... >> Memory Card operation is being executed. << Now loading... >> File is being loaded from Memory Card. << Now saving... >> File is being saved to Memory Card. << Now checking plug-in board. >> Plug-in Board is being checked (after powering up the synthesizer). << MIDI bulk receiving... >> MIDI Bulk data is being received. << MIDI bulk transmitting... >> MIDI Bulk data is being transmitted. << C 3:128[ ] Stored. >> Sound has been stored. << Completed. >> Operation has completed. << Are you sure ? [YES]/[NO] >> Final confirmation. << Overwrite? [YES]/[NO] >> There is a file already stored with the same name. Replace it with a newer one with that name? 144 g The following table provides troubleshooting hints and page references for some common problems. Most problems may be simply the result of incorrect set...