Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
The internal value is not affected. (3-4) NON-REGISTERED PARAMETER NUMBER STATUS 1011nnnn(BnH) n = 0 - 15 VOICE CHANNEL NUMBER LSB 01100010(62H) RPN LSB 0ppppppp p = NRPN LSB(see chart below) MSB 01100011(63H) RPN MSB 0qqqqqqq q = NRPN MSB(see chart below) DATA ENTRY MSB 00000110(06H) DATA VALUE 0mmmmmmm m = Data Value First, designate the parameter using NRPN MSB/LSB numbers. Then, set its value with data entry MSB/LSB. NRPN D.ENTRY MSB LSB MSB LSB PARAMETER NAME DATA RANGE 01H 08H mmH ---VIBRATO RATE 00H - 40H - 7FH (-64 - 0 - +63) 01H 09H mmH ---VIBRATO DEPTH 00H - 40H - 7FH (-64 - 0 - +63) 01H 0AH mmH ---VIBRATO DELAY 00H - 40H - 7FH (-64 - 0 - +63) 01H 20H mmH ---FILTER CUTOFF FREQUENCY 00H - 40H - 7FH (-64 - 0 - +63) 01H 21H mmH ---FILTER RESONANCE 00H - 40H - 7FH (-64 - 0 - +63) 01H 63H mmH ---EG ATTACK TIME 00H - 40H - 7FH (-64 - 0 - +63) 01H 64H mmH ---EG DECAY TIME 00H - 40H - 7FH (-64 - 0 - +63) 01H 66H mmH ---EG RELEASE TIME 00H - 40H - 7FH (-64 - 0 - +63) 14H rrH mmH ---DRUM INST FILTER CUTOFF FREQ. 00H - 40H - 7FH (-64 - 0 - +63) 15H rrH mmH ---DRUM INST FILTER RESONANCE 00H - 40H - 7FH (-64 - 0 - +63) 16H rrH mmH ---DRUM INST AEG ATTACK RATE 00H - 40H - 7FH (-64 - 0 - +63) 17H rrH mmH ---DRUM INST AEG DECAY RATE 00H - 40H - 7FH (-64 - 0 - +63) 18H rrH mmH ---DRUM INST PITCH COARSE 00H - 40H - 7FH (-64 - 0 - +63) 19H rrH mmH ---DRUM INST PITCH FINE 00H - 40H - 7FH (-64 - 0 - +63) 1AH rrH mmH ---DRUM INST LEVEL 00H - 7FH (0 - Max) 1CH rrH mmH ---DRUM INST PANPOT 00H ,01H - 40H - 7FH (random,left - center - right) 1DH rrH mmH ---DRUM INST REVERB SEND LEVEL 00H - 7FH (0 - Max) 1EH rrH mmH ---DRUM INST CHORUS SEND LEVEL 00H - 7FH (0 - Max) 1FH rrH mmH ---DRUM INST 00H - 7FH (0 - Max) VARIATION SEND LEVEL MSB 14H-1FH(for drum voices) are effective only when the channel is assigned to the drum voice. rrH : drum instrument note number (3-5) SYSTEM REAL TIME MESSAGES (3-5-1) ACTIVE SENSING STATUS 11111110 (FEH) Transmitted at every 175 msec. Once this code is received, the CS1x starts sensing. When no status nor data is received for over approximately 350 ms, MIDI receiving buffer will be cleared, and the sounds currently played and the sustain switch are forcibly turned off. In this case, each control data will be reset to a certain value. (3-5-2) TIMING CLOCK(Receive only) STATUS 11111000 (F8H) Selects whether the tempo clock of the Arpeggiator is controlled by internal clock or the timing clock of an external device via MIDI. (3-6) SYSTEM EXCLUSIVE MESSAGE (3-6-1)UNIVERSAL NON REALTIME MESSAGE (3-6-1-1)GENERAL MIDI MODE ON F0H 7EH 7FH 09H 01H F7H The following controller values will be reset. VOLUME 100 PAN Center PROGRAM CHANGE 1 (Grandpno) BANK SELECT MSB 0 REVERB DEPTH 4 PITCH BEND CHANGE 0 (Center) MODULATION 0 (Off) EXPRESSION 127 (Max) SUSTAIN SWITCH 0 (Off) SOSTENUTO SWITCH 0 (Off) RPN Not assigned PORTAMENT CONTROL Reset MIDI MASTER VOLUME 127 (Max) PITCH BEND SENSITIBITY 02 (2semitones) FINE TUNING 0 COURSE TUNING 0 (3-6-1-2)IDENTITY REQUEST(Receive only) F0H 7EH 0nH 06H 01H F7H (n = Device No. However, the CS1x can receive without the device Number setting) (3-6-1-3)IDENTITY REPLY(Transmit only) F0H 7EH 7FH 06H 02H 43H 00H 41H ddH ddH 00H 00H 00H vvH F7H dd;Device Number Code CS1x:10 02 vv;TG Support Level CS1x:01(XG) (3-6-2)UNIVERSAL REALTIME MESSAGE (3-6-2-1) MIDI MASTER VOLUME F0H 7FH 7FH 04H 01H llH mmH F7H Sets the MASTER VOLUME value. The value "mm" is used to set the master volume (the value "ll" will be ignored). MIDI Data Format (3-6-3)PARAMETER CHANGE (3-6-3-1) MIDI MASTER TUNING F0H 43H 1nH 27H 30H 00H 00H mmH llH ccH F7H Sets the MASTER TUNING value. The values "mm" and "ll" are used to set the master tuning (the values "n" and "cc" will be ignored). T = M*200/256-100 "T " indicates the actual tuning value.(-99 - +99) "M" is the one byte value consisting of MSB, 0 - 3 bits of "mm", and LSB, 0 - 3 bits of "ll". (3-6-3-2) XG SYSTEM ON Bin Hex 11110000 F0 Exclusive status 01000011 43 YAMAHA ID 0001nnnn 1n Device Number 01001100 4C Model ID 0aaaaaaa 00 Address High 0aaaaaaa 00 Address Mid 0aaaaaaa 7E Address Low 00000000 00 Data 11110111 F7 End of Exclusive When receiving this message, the internal tone generator will be reset to XG SYSTEM ON. All the parameters will be initialized and reset to each default values. Since approximately 50ms is required to execute this message, be sure to leave an appropriate interval before the subsequent message. (3-6-3-3) XG PARMETER CHANGE 11110000 F0 Exclusive status 01000011 43 YAMAHA ID 0001nnnn 1n Device Number 01001100 4C Model ID 0aaaaaaa aaaaaaa Address High 0aaaaaaa aaaaaaa Address Mid 0aaaaaaa aaaaaaa Address Low 0ddddddd ddddddd Data || 11110111 F7 End of Exclusive For parameters with data size of 2 or 4, transmit the appropriate number of data bytes. See MIDI Data Table (page 22-25) for Address and Byte Count. The following four types of data are transmitted/received (Transmitted only when receiving parameter change request). XG Syste...