And each time the FILL IN 2 button is pressed, the FILL IN 2 pattern plays, and then the style changes in the 1 -* 2 3 -♦ 4 order. ■ MUSIC STYLE ARRANGER mode You can define which panel settings change by pressing a FILL IN button when the MUSIC STYLE ARRANGER is used. 1. Press and hold the MUSIC STYLE ARRANGER button for a few seconds. • The display changes to the following. T >->n J= iCu MSA MODE SET Sound&Rhy t hm DRUMS ACCOUP1 ACCOUP1 ACC0MP1 BASS LEFT RIGHTS RK3HT1 (continued on the next page) 55 Practical applications Practical applications Part III Playing the rhythm 2. Use the LEFT a and v buttons to select the mode. [Rhythm]: Only the rhythm changes. [Sound & Rhythm]: Both the sound and rhythm change. [Panel Memory]: The PANEL MEMORY number changes (A1 to A4). • After a few seconds, the display exits the setting mode. Panel Memory (KN720) (KN920/KN1500) PANEL MEMORY stores the panel set up of this instrument allowing you to make complex changes at the push of a single button. How to store the panel settings Store a different panel setting in each of the number buttons (0 to 9). I.Set up the desired panel settings (sounds, volumes, etc.) 2. While pressing the PANEL MEMORY button, press the number button for the memory you want to store (0 to 9). 0 12 3 □□□□ />\ 4 5 6 PANEL МДОртГ -О- Ч/ 7 В 9 □ □□□О • The current panel settings are now stored in the specified PANEL MEMORY number. To recall the stored settings, just turn on the PANEL MEMORY button, and press the number for the desired panel setup. Five panel setups can be stored in each of the two banks (A and B). 1. Set up the desired panel settings (sounds, volumes, etc.) 2. Use the BANK button in the PANEL MEMORY section to select a bank (A or B). 3. While pressing the SET button, press a number button (1 to 5) for the memory you want to store. -PANEL MEMORY- , BANK SET 1 2 3 4 5 C0 □□□□□ • The current panel settings are now stored in the specified bank and number. To recall the stored settings, select the BANK and specify the number. • The recalled settings can be changed manually; however the memory contents of the PANEL MEMORY remain unchanged until you store them again. • KN720: The contents stored in the PANEL MEMORY can be saved in this instrument’s memory. (Refer to page 87.) • KN920/KN1500: The PANEL MEMORY settings can be saved on a disk for recall at a later time. (Refer to page 89.) 56 Part ni Playing the rhythm ■ PANEL MEMORY mode You can define which panel settings are stored when the PANEL MEMORY is used. 1. Press and hold the PANEL MEMORY button (KN720)/SET button (KN920/KN1500) for a few seconds. • The display changes to the following. 7e iDfl J= iCU PAGE A Pi P MEM MODE No r m a \ DRUMS tccoun ACCOUW *cco5fi baSS Ceft righto righti 2. Use the LEFT a and v buttons to select the mode. Normal: The sounds and volume balance, effects and CONDUCTOR status are stored. Expand: All the instrument’s settings are stored, including the rhythm, TRANSPOSE, tempo, etc. • After a few seconds, the display exits the setting mode. ■ EXPAND MODE FILTER You can specify which data is stored in the Expand mode. 1. While the P.MEM MODE display is shown, 4. Repeat steps 2 and 3 for each item, as desired, press the PAGE a button. • The display looks similar to the following. 2. Use the ACCOMP 1 a and v buttons to select the item. • Select from [Rhythm], [Tempo], [Split Pt] {SPLIT POINT), [Transpos], [APC&Mem] (AUTO PLAY CHORD & MEMORY), [MIDI], [Key Scale], [Reverb], [CHO Set] (CHORUS Setting) (KN720), [DSP Set] (KN920/KN1500), and [P4-P16 Set] (PART 4 to 16 Setting). 3. Use the RIGHT 1 a and v buttons to store the on or off status for the selected item (On/Off). Suggestions for using PANEL MEMORY • The initial factory setting of PANEL MEMORY contains professional settings which you may choose to use or to alter to your own taste. These can be restored at any time by initializing the PANEL MEMORY. (Refer to page 122.) • You can change from one PANEL MEMORY to another by pressing the optional Foot Switch (sold separately). 57 Practical applications Practical applications Part III Playing the rhythm Foot Switch setting r □ CD A CED CD ' N nil a □ a - : ni i:i:i3 c{3 m i i:i3 rT~t -ii oci:i:o or A O III 1 1 1 IM Ö n rTTTTTm n O O DC hd œdchj a CD a □ mp:i:i □ You can assign various functions to the optional Foot Switch (sold separately). The assigned function can then be controlled with the Foot Switch. Assigning (unctions 1. Press the MEMORY & CONTROL button to 4. Use the LEFT a and v buttons to select a turn it on. desired function. MEMORY & CONTROL O • The display changes to the following. 7® i“in J- icu UEWPAGE i p 1 M E M& CONTROL Load Save DRUMS ACCOUPl ACCOMP? ACCOH*ï BASS CEFT HIQHT3 RIGHT 1 2. Use the PAGE buttons to select [P3 Foot Switch] (KN720)/[P5 Foot Switch] (KN920/ KN1500). • The display changes to ...
)
