Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Note: * if you don’t do anything for 3 seconds the LED stops flashing and shows the current PROGRAM CHANGE number. * if the number you input is over 127, it will return to the previous LSB or MSB value. 14. Selecting a VELOCITY CURVE The VELOCITY CURVEs determine the relationship between how hard the keys are struck and the corresponding velocity that the unit transmits. This unit allows you to select from 12 VELOCITY CURVEs. Simultaneously press the CHANNEL and MEMORY switches. The LED starts to flash showing the current number of the VELOCITY CURVE. Press one of the numeric keys to select a VELOCITY CURVE. The 10 key numbers correspond to the first 10 VELOCITY CURVEs as follows: You can also use the “+” or “-” switches to access all the VELOCITY CURVEs. There are 3 Fixed VELOCITY CURVEs which output the following velocity values: Curve Velocity F 0 64 F 1 100 F 2 127 These are achieved by selecting velocity curve 09. F0 will appear on the LED. Use the “+” or “-“ keys to select F0F2. Note: If you don’t do anything for 3 seconds the LED stops flashing and shows the current PROGRAM CHANGE number. 15. MIDI OUT FROM USB The MIDI output connector is normally used to send MIDI data from the keyboard. If the keyboard is connected to a computer using USB the MIDI Out can also be used to send data received from USB. Pressing both ‘MIDI OUT FROM USB’ buttons flashes the current setting on the LCD display. The +/- keys can be used to alter the current setting. + selects YES, - selects NO. Pressing both + and – calls up the default setting which is NO. When ‘NO’ is selected the MIDI Out sends the data from the keyboard. When YES is selected the MIDI Out sends the MIDI data received from USB. The status of MIDI OUT FROM USB will be saved in non-volatile memory and restored when the keyboard is switched on again. The factory default is set to NO 16. GM RESET (GENERAL MIDI RESET) – Evolution 249/361 Only This function allows you to send a GENERAL MIDI MODE RESET message. Press the BANK LSB and BANK MSB keys together. Hold the keys down for at about 2 seconds and the reset message is sent. Evolution 225C/249C/361C Only 17. Assignable Rotary controllers All these assignable controllers are selected by the ‘CONTROL SELECT’ & 'CONTROL ASSIGN' functions for these keyboards. ‘Assignable Controllers’ refers to any of the 8, 12 or 16 assignable Knobs and also includes the assignable Wheel and Slider. The Slider is Assignable Controller 13 or 17(for MK249C and MK-361C only), the Wheel is Assignable Controller 9, 14 or 18. The basic operation is:Press the CONTROL SELECT buttons together. Select the controller by moving it or by typing the number in. Press the CONTROL ASSIGN buttons and enter the new number using the keypad. To change one of the assignable controllers, the keyboard uses the following method: Press both 'CONTROL SELECT' buttons and release. The LED display shows the current Controller which has been selected. The LED’s toggle between the controller number and the assigned value. E.g. initially it would toggle between c14 & 01, showing that the Wheel is assigned to the Modulation Wheel controller. Select a controller by moving any one of the assignable controllers, the numeric keypad or the +/- keys. The LED then toggles the display between the new controller and its assignment. Repeat this process to see the controller number assignment (0-132) for any Knob, Slider or the Wheel, by moving the relevant controller or by typing a new number. If no keys are pressed or any of the assignable controllers moved, the LED display stops flashing after 3 seconds and returns to normal operation. Press both 'CONTROL ASSIGN' buttons and release. The number entered at this point will be assigned to the last selected controller. The numeric entry uses the standard data entry system. (see section on Entering Numbers) If a complete number is entered the display stops flashing and the new assignment is stored. If the +/- keys are used, the revised value is shown on the LED display and the flashing time-out is reset. Once a controller has been assigned the current knob/slider/wheel position should be sent out. This ensures that when the controller if first moved it does not trigger a large jump from it’s previous setting. During the data entry stage while the LED display is flashing, the Knobs, Slider and the Wheel do not function. The MIDI keyboard should continue to function at all times 18. Snap Shot When both SNAP SHOT keys are pressed the MK-249C sends out the settings for all of the Assignable Controllers on the current selected channel. This feature lets you record the settings of the Knobs, Slider & Mod Wheel into your sequencer. 19. SPECIFICATIONS Evolution 249: 1. Keyboard: 49 standard keys (Velocity sensitive) 2. Control: Switches: (WHEEL, CHANNEL, PROGRAM, MEMORY, TRANSPOSE, GM RESET, VEL CURVE, BANK LSB, BANK MSB, OCTAVE DOWN, OCTAVE UP, POWER ON/OFF, Numeric Keys (0-9), , +) 3. Control: Sliders: (PITCH BEND WHEEL, MODULATI...
Эта инструкция также подходит к моделям:Синтезаторы/фортепиано - 249 (217.3 kb)