Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Before using your new Kenmore machine, please pause for a moment and carefully read this booklet which contains instructions on how to operate and care for your machine. Specific instructions are gLven on threading, tension adjustments, cleaning, oiling, etc. This will help you obtain the best sewing results and avoid unnecessary service expense tor conditions beyond our control. Advtce on tile operation and care of your machine is always available at your nearest Sears Retail Store. Please remember, if you have questions about your machine or need parts and service, always mention the model number and serial number when you inquire. Safety Cautions: e Be sure that the electrical voltage of the wall outlet (wall receptacle) is the same as the rated voltage of the motor. e Disconnect the power supply plug from the wall outlet when changing needles, presser foot or needle plate, or when leaving the machine unattended. This efiminates the possibility of sta_ing the machine by accidentally pressing the foot control. e All covers must be closed when operating the machine. e Do not pull the fabric while you are stitching as this may deflect the needle, causing it to break. e Before cleaning your machine, disconnect the power supply plug from the walt outlet. e Do not attempt to adjust the motor belt. Contact your nearest Service Center should any adjustment be required. e Handle the foot control with care and avoid dropping it on the floor. Be sure not to place anything on top of it. e Closely watch the area being sewn to avoid injuries from needles and knives. e Use only the handle to lift and move the machine, Kenmore Overiock Record in space provided below the model number and serial number of this appliance. The model number and serial number are located on the nomenclature plate, as identified on Page 3 of this booklet. Model No, 385, Serial No. Retain these numbers for future reference. SECTION SECT! ON SECTION 1. KNOW YOUR MACHINE Locate and Identify the Parts ............... Identify the Accessories ..................... 2. PREPARE YOUR MACHINE FOR SEWING Plug in the Machine and Switch on the Power .... Foot Control Use .... ...................... How to Turn Hand Wheel ....................... Opemng and Closing the Side Cover ................ Opening and Closing the Looper Cover ............. The Position of Thread Guide Bar ............... Attaching the Spool Cap and Net ............... Raising or Lowering the Presser Foot ............... Threading the Machine ..................... e Threading the Lower Looper ............... e Threading the Upper Looper ............. e Threading the Needle on the Right ........... e Threading the Needle on the Left ............ 3. LEARN THE STITCHES Starting Sewing ........................ Finishing Sewing ........................... Sewing Continuously ........................ Securing Ends ........................... Thread Tension (4 threads) ................... Threading the Machine (3 threads) ................ Thread Tension (3 threads) ................... Adjustment of Stitch Length ................... Adjustment of Foot Pressure ................... Removing the Presser Foot ..................... TABLE 3_4 4 5 5 6 6 6 7 7 8 9_17 t0_11 12"13 14_15 t6_17 18 !8 18 19_20 21"_23 24 24_25 26 26 27 OFCONTENTS Attaching the Presser Foot .................... 27 Changing Needle ........................... 28 To Disengage the Upper Knife .................. 29 To Engage the Upper Knife ...................... 29 Types of Needle Plates ....................... 30 Changing the Needle Plate ..................... 30 Thread and Needle Chart ................... 31 Rolled Hemming, Picot Edging and Narrow Hemming ........................ 32_34 Decorative Overedging .................. 35 Pin Tucking .............................. 36 SECTION 4. CARE FOR YOUR MACHINE Cleaning Upper Knife Area .................. 37 Cleaning the Feed Dog ..................... 37 Replacing the Light Bulb .................... 38 Oiling the Machine .......................... 39 Replacing the Upper Knife ................... 40 SECTION 5. PERFORMANCE PROBLEMS CHART What to Do When ........................ 4t PARTS LIST ........................................ 42 INDEX ............................................ 43 Specification of the Machine .............................. 44 Carrying handle Thread guide bar Right needle -Stitch dial tength Thread guide Face plate \ thread tension dial Spool pin Thread take-up lever Spool holder thread gude Let[ needle Spool stand thread tension dia! Need le thread guide Rigilt needle tllread guide NomencLature plate Side cover Upper looper thread guide (t) Upper looper thread Plug tension dial connector Lower thread looper gude (1) Power switch Hand wheel Lower looper thread tension dial Looper cover Looper thread guide Foot control Needle clamp Upper knife Needle ptate Presser foot Needle plate screws set screw Needle bar thread guide Needle clamp Foot holder Upper looper / ...