Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
Memo • You can pull up the bobbin thread after threading the upper thread (“UPPER THREADING” on page 57). a Guide the bobbin thread through the groove, following the arrow in the 1 Getting Ready Note • If the thread is not correctly inserted through the tension spring of the bobbin case, it may cause incorrect thread tension. (see page 79) a Tension spring• CAUTION Be sure to hold down the bobbin with your finger and unwind the bobbin thread correctly. Otherwise, the thread may break or the thread tension will be incorrect. h Insert the tab in the lower-left corner of the illustration. * Do not cut the thread with the cutter. * Do not replace the bobbin cover. b While holding the upper thread, press the “Needle Position” button to lower the needle. a “Needle Position” button c Press the “Needle Position” button to raise the needle. d Gently pull the upper thread. A loop of the bobbin thread will come out of the hole in bobbin cover (1), and then lightly press the needle plate. down on the right side to close the cover (2). LOWER THREADING e Pull up the bobbin thread, pass it under the presser foot and pull it about 100 mm (approx. 3-4 inches) toward the back of the machine, making it even with the upper thread. a Upper thread b Bobbin thread f Replace the bobbin cover. UPPER THREADING UPPER THREADING a Turn the main power to ON. Upper Threading 1 Press > > > > in this order to display a video example of the operation on the LCD (see page 46). Follow the steps explained below to complete the operation. CAUTION • Be sure to thread the machine properly. Improper threading can cause the thread to tangle and break the needle, leading to injury. • When using the walking foot, the side cutter or accessories not included with this machine, attach the accessory to the machine after threading the machine. Memo • The automatic threading function can be used with sewing machine needle sizes 75/ 11 through 100/16. • Thread such as transparent nylon monofilament thread and thread with a thickness of 130/20 or thicker cannot be used with the automatic threading function. • The automatic threading function cannot be used with the wing needle or the twin needle. b Press the “Presser Foot Lifter” button to raise the presser foot. Getting Ready > The upper thread shutter opens so the machine can be threaded. a Upper thread shutter Memo • This machine is equipped with an upper thread shutter, allowing you to check that the upper threading is performed correctly. c Press the “Needle Position” button to raise the needle. Note • If you try to thread the needle automatically without raising the needle, the thread may not thread correctly. UPPER THREADING d Pivot the spool pin so that it angles upward. Set the thread spool on the spool pin so that the thread unwinds from the front of the spool. a Spool pin b Spool cap c Thread spool d Spool felt e Push the spool cap onto the spool pin as far as possible, then return the spool pin to its original position. CAUTION • If the thread spool and/or spool cap are set incorrectly, the thread may tangle on the spool pin and cause the needle to break. • Use the spool cap (large, medium, or small) that is closest in size to the thread spool. If a spool cap smaller than the thread spool is used, the thread may become caught in the slit on the end of the spool and cause the needle to break. Memo • When sewing with fine, cross-wound thread, use the small spool cap, and leave a small space between the cap and the thread spool. a Spool cap (small) b Thread spool (cross-wound thread) c Space f While holding the thread with both hands, pull the thread up from under the thread guide plate. a Thread guide plate g While holding the thread in your right hand, pass the thread through the thread guide in the direction indicated. h Guide the thread down, up, then down through the groove, as shown in the illustration. Memo • Look in the upper groove area to check if the thread catches on the take-up lever visible inside the upper groove area. a Look in the upper groove area UPPER THREADING i Pass the thread through the needle bar thread guide (marked “6”) by holding the thread with both hands and guiding it as shown in the illustration. aNeedle bar thread guide 1 j Press the “Presser Foot Lifter” button to lower presser foot. k Pass the thread through the thread guide disks (marked “7”). Make sure that the thread passes through the groove in the thread guide. Getting Ready Note • When using thread that quickly winds off the spool, such as metallic thread, it may be difficult to thread the needle if the thread is cut. Therefore, instead of using the thread cutter, pull out about 80 mm (approx. 3 inches) of thread after passing it through the thread guide disks (marked “7”). a80 mm (approx. 3 inches) or more l Pull the thread up through the thread cutter to cut the thread, as shown in the illustration. a Thread cutter a Groove in thread guide m Press the “Automatic Threading” button to have the machine automat...
Эта инструкция также подходит к моделям:Швейные машинки - Innov-is Ie (23.04 mb)