Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
k Embroidery unit Attach the embroidery unit to the machine, and then attach the embroidery frame. l Thread cutter Pass the threads through the thread cutter to cut them. m Needle threader lever Use the needle threader lever to thread the needle. n Thread take-up lever check window Look through the window to check the position of the take-up lever. — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Needle and embroidery foot section Right-side/rear view a Thread guide disk Pass the thread through the thread guide disk when using the needle threader to thread the needle. a Handle Carry the machine by its handle when transporting the machine. b Needle bar thread guide Pass the upper thread through the needle bar thread guide. b Handwheel Turn the handwheel toward you (counterclockwise) to raise and lower the needle. c Needle plate When the needle is lowered, it enters the hole in the needle plate. c d Embroidery card slot Insert the embroidery card. Air vent d Needle plate cover Remove the needle plate cover to clean the bobbin case and race. The air vent allows the air surrounding the motor to be exchanged. Do not cover the air vent while the machine is being used. e Bobbin cover/bobbin case Remove the bobbin cover, and then insert the bobbin into the bobbin case. e Power supply jack Insert the plug on the power supply cord into the power supply jack. f Embroidery foot “Q” This presser foot is used for embroidering. f Main power switch Use the main power switch to turn the machine on and off. Memo • Refer to pages 8 through 11 while you are learning to use your machine. — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Operation buttons — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Operation buttons The operation buttons help you to easily perform various basic machine operations. a Start/stop button Press the start/stop button to start or stop embroidering. The machine embroiders at a slow speed while the button is pressed. When embroidering is stopped, the needle is lowered in the fabric. The button changes color according to the machine’s operation mode. Green: The machine is ready to embroider or is embroidering. Red: The machine can not embroider. Orange: The machine is winding the bobbin thread, or the bobbin winder shaft is moved to the right side. b Needle position button Press the needle position button to raise or lower the needle. Pressing the button twice sews one stitch. c Thread cutter button Press the thread cutter button after embroidering is stopped to cut both the upper and the bobbin threads. CAUTION . Do not press the thread cutter button after the threads have already been cut, otherwise the needle may break, the threads may become tangled or damage to the machine may occur. Note • Do not press the thread cutter button if there is no fabric under the presser foot or while the machine is embroidering, otherwise damage to the machine may occur. • When cutting thread thicker than #30, nylon thread or other special threads, use the thread cutter on the side of the machine. — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Operation panel — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Operation panel The front operation panel has an LCD (liquid crystal display) and operation keys. a c d e b h fg a ttern type selection screen. For details, refer “ operations. b Back key c d Next page key e Memory key Press to store patterns in the machine's memory. — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — 1 1 GETTING READY The various preparations to start embroidering are described in this chapter. Embroidery Step by Step ......................................................................................... 14 Attaching the Embroidery Unit................................................................................ 15 Embroidery unit precautions .............................................................................. 15 Attaching the embroidery unit ........................................................................... 15 Removing the embroidery unit ........................................................................... 16 Turning the Machine On/Off .................................................................................. 18 Power supply precautions .................................................................................. 18 Turning on the machine ..................................................................................... 19 Turning off the machin...
Эта инструкция также подходит к моделям:Швейные машинки - PE-770 (1.59 mb)
Швейные машинки - PE-700II/750D(USB) (1.59 mb)
Швейные машинки - PE-700/750D (1.59 mb)