Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
1 Turn on the machine. Turn on the sewing machine. For details on turning on the machine, refer to “Power supply” (page 9). v 2 Select the stitch. Select the stitch appropriate for the area to be sewn. For details on selecting a stitch, refer to “Selecting stitching” (page 27). v 3 Attach the presser foot. Attach the presser foot appropriate for the stitch. For details on replacing the presser foot, refer to “Replacing the presser foot” (page 24). v 4 Start sewing. Position the fabric, and then start sewing. When sewing is finished, cut the threads. For details on starting to sew, refer to “Starting to sew” (page 28). Selecting stitching Using the stitch selection keys, select the desired stitch. When the sewing machine is turned on, the straight stitch ( left needle position) is selected. Turn on the sewing machine. a b Press (stitch selection keys). The number of the selected stitch is displayed. Press the “+” or “–” side of to increase or reduce the number by one. Pressing on the right changes the digit on the right and pressing on the left changes the digit on the left. • The stitch is selected. Attach the presser foot indicated in the LCD. c a a Presser foot type • For details, refer to “Replacing the presser foot” (page 24). Memo . The presser foot to be used is indicated by the letter (J, A, etc.) that appears above the stitch number. d If necessary, adjust the stitch length and width. • For details on sewing with each of the utility stitches, refer to the following example. ¦ [Example] Selecting stitch . Press the stitch selection keys to select stitch 04. a With on the right, select “4”, and with on the left, select “0”. b Press the “+” or “–” side of (stitch length adjustment key) to increase or reduce the stitch length. a Stitch length adjustment key b Short c Long Press the “+” or “–” side of (stitch width c adjustment key) to increase or reduce the stitch width. a Stitch width adjustment key b Narrow c Wide Note . When the stitch length or stitch width is changed from the standard setting, around or disappears from the LCD. When the stitch length or stitch width is reset back to the standard setting, reappears around or in the LCD. . If the stitch width of the selected stitch cannot be adjusted, “--” appears to the right of in the LCD. CAUTION . After adjusting the stitch width, slowly turn the handwheel toward you (counterclockwise) and check that the needle does not touch the presser foot. If the needle hits the presser foot, the needle may bend or break. . If the stitches are bunched together, increase the stitch length. Continuing to sew with the stitches bunched together may result in the needle bending or breaking. 27 SEWING BASICS SEWING BASICS Starting to sew Raise the needle by turning the handwheel a toward you (counterclockwise) so that the mark on the wheel points up. (With models equipped with (needle position button), raise the needle by pressing once or twice.) or a Mark b Needle position button b Raise the presser foot lever. a Presser foot lever Place the fabric under the presser foot, pass c the thread under the presser foot, and then pull out about 5 cm (2 inch) of thread toward the rear of the machine. a 5 cm (2 inch) d While holding the end of the thread and the fabric with your left hand, turn the handwheel toward you (counterclockwise) with your right hand to lower the needle to the starting point of the stitching. Lower the presser foot lever. e a Presser foot lever f On models equipped with a sewing speed controller, slide the sewing speed controller to the left or right to adjust the sewing speed. Refer to “Sewing speed controller (for models equipped with the start/stop button)” (page 10). a Sewing speed controller Slowly press down on the foot controller. g (start/stop (With models equipped withbutton), if the foot controller is not connected, press once.) or aStart/stop button • The machine starts sewing. h Take your foot off the foot controller, or press (start/stop button)) (needle position button), once or twice.) (start/stop button) once (if the machine was started by pressing (for models equipped with the start/stop button). ..The machine stops sewing. iRaise the needle by turning the handwheel toward you (counterclockwise) so that the mark on the wheel points up. (With models equipped withraise the needle by pressing j Raise the presser foot lever. k Pull the fabric to the left side of the machine, and then pass the threads through the thread cutter to cut them. a Thread cutter Memo .When the foot controller is plugged in, (start/stop button) cannot be used to start sewing. .When sewing is stopped, the needle remains lowered (in the fabric). The machine can be set so that the needle will stay up when sewing is stopped. For details on setting the machine so that the needles stay up when sewing is stopped, refer to “Changing the needle stop position” (page 10). ¦Sewing reinforcement stitches When sewing stitches other than straight or zigzag stitches that are se...
Эта инструкция также подходит к моделям:Швейные машинки - HS-2000 (2.69 mb)