Производитель: Brother
Размер: 4.18 mb
Название файла:
|
Фрагмент инструкции
NOTE: Make sure to thread only through the upper thread take up 7. 6. Pass the thread through the eye of the upper looper 9. NOTE: If the upper looper thread breaks during sewing: This may be caused by the lower looper thread getting caught on the upper looper. If this happens, lower the upperlooper by turning the hand wheel, remove the lower looper thread from the upper looper, and re-thread the upper looper from at least the tension disc. EnglishThreading the left needle 1. Slide the change switch to the left until it is aligned to the "L" mark on the machine. 2. Run the thread in the sequence illustrated, following the yellow color and the numbers next to each threading point. Two needles One needle 213456734 7a) Pull the thread off the spool and directly up through the thread holder 1 and the thread holder 2 on the thread tree from back to front. b) Hold the thread with your left and right hands, then pass the thread through the thread guide 3, and then pass the thread through the tension disc 4 which is in the channel next to the yellow tension adjustment dial. c) Guide the thread down the channel and across through the threading points 5 6 7 next to the yellow color marks following the numerical order in the accompanying illustration. NOTE: Make sure the thread is through the left of the separater . CAUTION · Turn off the machine before threading for safety. · Turn the hand wheel so that the mark on the hand wheel is aligned to the line on the machine (See CHAPTER 1 "Turning direction of hand wheel"). Threading the right needle 1. Slide the change switch to the right until it is aligned to the "R" mark on the machine. 2. Run the thread in the sequence illustrated below, following the green color and the numbers next to each threading point. 213456734 Two needles One needle 7a) Pull the thread off the spool and directly up through the thread holder 1 and the thread holder 2 on the thread tree from back to front. b) Hold the thread with your left and right hands, then pass the thread through the thread guide 3, and then pass the thread through the tension disc 4 which is in the channel next to the green tension adjustment dial. c) Guide the thread down the channel and across through the threading points 5 6 7 next to the green color marks following the numerical order in the accompanying illustration. NOTE: Make sure the thread is through the right of the separater . EnglishThreading the left needle 1. Slide the change switch to the left until it is aligned to the "L" mark on the machine. 2. Run the thread in the sequence illustrated, following the yellow color and the numbers next to each threading point. Two needles One needle 213456734 7a) Pull the thread off the spool and directly up through the thread holder 1 and the thread holder 2 on the thread tree from back to front. b) Hold the thread with your left and right hands, then pass the thread through the thread guide 3, and then pass the thread through the tension disc 4 which is in the channel next to the yellow tension adjustment dial. c) Guide the thread down the channel and across through the threading points 5 6 7 next to the yellow color marks following the numerical order in the accompanying illustration. NOTE: Make sure the thread is through the left of the separater . CAUTION · Turn off the machine before threading for safety. · Turn the hand wheel so that the mark on the hand wheel is aligned to the line on the machine (See CHAPTER 1 "Turning direction of hand wheel"). Threading the right needle 1. Slide the change switch to the right until it is aligned to the "R" mark on the machine. 2. Run the thread in the sequence illustrated below, following the green color and the numbers next to each threading point. 213456734 Two needles One needle 7a) Pull the thread off the spool and directly up through the thread holder 1 and the thread holder 2 on the thread tree from back to front. b) Hold the thread with your left and right hands, then pass the thread through the thread guide 3, and then pass the thread through the tension disc 4 which is in the channel next to the green tension adjustment dial. c) Guide the thread down the channel and across through the threading points 5 6 7 next to the green color marks following the numerical order in the accompanying illustration. NOTE: Make sure the thread is through the right of the separater . 17 Threading the needle Threading the needle (using the needle threader) The needle can be threaded by one-touch operation using the needle threader. 1. Lower the presser foot lever 1 to lower the presser foot. 2. Pull the end of the thread, which has been passed through the needle bar thread guide 2, to the left, then pass the thread through the notch of the thread guide 3, and then firmly pull the thread from the front and insert it into the slit of the thread guide disk 4 all the way. NOTE: Make sure that the thread passes the notch of the thread guide...
Эта инструкция также подходит к моделям:Швейные машинки - 4234DT (4.18 mb)
Швейные машинки - 4234D (4.18 mb)