Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Put the darning plate on the needle plate No presser (see p. 233). foot 2. Remove presser foot, stretch fabric between Darning plate embroidery hoops with hole centered. 3. Draw the bobbin thread up through the fabric by holding the top thread and taking one stitch at the spot where you wish to start darning. 4. Lower the presser bar and sew at a slow speed. 5. Move the fabric back and forth slowly until you have covered the darning area. 6. Turn the fabric half turn and sew another layer of stitching over the first layer. NOTE: If your fabric is thin or badly damaged, use a separate piece of fabric under the hole to reinforce it. 7. When you finish darning, remove the darning plate. Set the Machine Stitch selector Top thread tension control 2 _o 6 Stitch length ! o % Straight foo= Zigzag foot Stretch stitching was developed to be used on stretch fabrics and knits. It can be used on other The Stitch and Its Uses fabrics as well. It works well on This stitch is the stretch variation of curved seams and on any the straight stitch, especially develop-garments that will receive a great ed for knits and stretch fabrics. deal of strain (ie. children's T,his stitch can also be used for clothes). topstitching on all fabrics. The stretch stitch does not actually stretch as it is being sewn, but is stitched in a forward and back motion (sometimes called a "reverseaction" stitch), so that it will give when the fabric stretches instead of breaking. • Basic Zigzag Set the Machine Stitch selector @ Stitch length Top thread tension 6 to 24 control 2 to 5 Z;gzag foot The Stitch and Its Uses The zigzag stitch is one of the most common and most versatile stitches on your machine. Itcan be a utility stitch for sewing buttons, buttonholes, hemming, overcasting, mending and darning. It can also be used to decorate with trims, appliques and cut-out work or as a decorative stitch. Here's How There are many ways to sew a zigzag stitch. Consult the specific variations for detailed directions, Satin Stitch p. 26 Applique Work p. 27 Bar Tacking p. 27 Monogramming p. 28 Embroidery p. 28 Button Sewing p. 29 Overcasting p. 30 • Satin Stitch Set the Machine Stitch selector I Stitch length 0 to 24 Top thread tens;or, control 1 to 4 <, Satin stitch foot The Stitch and Its Uses The Satin stitch is a versatile and often used decorative stitch, but it can also be used to overcast a raw edge (for ex ample, blankets, linens, and napkins). The Satin stitch is especially in applique, bar tacking, ming and embrodiery. tablecloths attractive monogram- Zigzag width : Shtch length : 24 !2 > > > Close to 0 Here's How Once your machine is set up to stitch, you may want to experiment on a fragment of the fabric you are planning to use. Too tight a satin stitch may pucker some light weight fabrics. Stitch selector Stitch length 0 to 24 Top thread tension control 1 to 4 Satir, stitch foot Bar Tacking Set the Machine Stitch selector Stitch length 1 Top thread tension 0 contro_ 1 to 4 Baste (or fuse with iron-on fabric This stitch is similar to a very short joiner) applique pieces on the fabric. satin stitch and is used to reinforce Stitch around sure the needle the applique fails along making the outer \ points pockets of strain and straps such as corners on lingerie. or edge of the applique, Zigzag foot Sew 4 to 6 zigzag stitches. When sewing corners, lower the needle down into the fabric. Raise the presser foot and pivot the fabric to the right or left. + Monogramming Set the Machine Stitch selector Stitch ength 0 to 24 Top thread tens_en control 1 to 4 k, Here's How 1. Set the same as satin stitch. 2. Back the fabric with paper or Satin stitch foot interfacing. !. 3. Draw the design on to the fabric with tailor's chalk. 4. Satin stitch, adjusting the stitch width as necessary to form each pattern. 5. If using paper, carefully remove it when you have finished sewing. • Embroidery f Set the Machine Stitch selector Top thread tension Stitch length 6ontrol 1 to 4 Any number tO adjust) Here's How _. (not necessary 1. Put the darning plate on the needle plate (see p. 2__33). No presser O) Remove presser foot. foot 2. 3. Adjust the stitch width as desired -Darning plate (see p. 1__8). 4. Draw the design on to the fabric with tailor's chalk. 5. Stretch the fabric between embroidery hoops and place under the needle. 6. Lower the presser foot lever to engage the top thread tension. 7. Holding the top thread in your left hand, rotate the hand wheel toward you one comp[ete turn. Pull the top thread to draw the bobbin thread through to the surface of the fabric. 8. Using a medium speed, stitch along the marked outline, guiding the fabric carefu Ily by hand. Sew a Button Set the Machine Stitch selector ! '_-.%':'._-:,b.-_"t:i_-_L:,: '":_-'"-_? -'''__::-"_" °71 Top thread tension control 1 to 4 Stitch tength Any number (not necessary Zigzag foot tO adjust}O' Use the darning plate for button I. Set the stitch selector at the 2. Align the both holes of the sewing (see p...
Эта инструкция также подходит к моделям:Швейные машинки - 385.101118 (2.77 mb)