Оценок - 5, средний балл: 4.2 ( )

Производитель: Euro-Pro Размер: 4.32 mb Название файла: Язык инструкции:

elastic fabrics and stretch lace, lingerie stretch knit. Simply stitch elastic into place, making sure it is The stitch is decorative as well as useful. evenly spaced. To do this, mark the correct length piece into quarters, then match these markings with center front and side seams. Model 377 Model 374 Model 373/372 Presser foot zigzag foot zigzag foot Pattern selector C ( ) F( ) Stitch length dial 1 to 2.5 1 to 2.5 Presser foot zigzag foot Pattern selector C( ) Stitch length dial S.S. DECORATIVE EDGING Turn the raw edgeunder 2cm and press. Place the fabric right side up with the middle of the turnover under the center of the presser foot, so that the stitch sews on to the fold and just over the raw edge underneath. SEWING BUTTONHOLES The built -in buttonhole mechanism of this machine makes it possible to sew button holes in a short time without turning the material. Model 377/374 Model 373/372 Presser foot buttonhole foot buttonhole foot Pattem selector Stitch length dial 0.5 to 1 Raise the foot and the needle to its highest position. Replace the foot with the transparent buttonhole foot for sewing buttonholes. Mark the location and the desired length of buttonhole on the fabric using a , pencil or tailor s chalk. Note: (Model EP 377 and 374 only) * The mark on the stitch*To find the most suitable length dial shows a range of stitch length, it is better buttonhole sewing. An to sew a sample buttonhole adjustment can be made on a piece of waste fabric. by setting the mark, as * When sewing very fine shown. fabrics and synthetics, de* Buttonhole stitch length is crease the pressure of foot adjustable only on one side. and sew over a piece of paper to prevent yarn distortion. 14 HEMMING (Model 377 only) Presser foot hemmer foot Pattern selector M( ) Stitch length dial 1 to 4 Raise the foot and the needle to its highest position. Replace the foot with the hemmer foot. Fold over the fabric edge by about 3mm (1/8 inches ) and place it under the foot. Secure the folded edge with a few stitches. Take out the workpiece and draw the hem into the hemmer foot by pulling on the threads. Lower the foot and swe the hem. During sewing, fold the fabric to the left a little and allow it to run into the hemmer foot. Make sure that the fabric does not move under the right half of the foot. The fabric must be fed into the scroll of the hemmer sufficiently so that the workpiece edge runs freely through the groove under the foot. SEWING BLIND HEMS (Model 377/374/373/372) Model 377 Model 374 Model 373/372 Presser foot blind hem foot blind hem foot Pattern selector B ( ) E( ) Stitch length dial 1 to 3 1 to 3 1. Turn up the hem to the desired width and press. ( Fig. 1) 2. Fold hem back against the right side of the garment with top edge of hem extending about 4 mm (1/6 inches) to the right side of the garment folded. (Fig. 2) 3. Place the garment under the foot so that double-folded edge runs along the hemlguide and lower the foot. Sew slowly for better control, making sure the narrow zigzag stitches are sewn on the hem edge and wide zigzag stitches will just catch one thread of folded edge. (Fig. 3) 4. Unfold the fabric and you will have a bling stitch hem (Fig. 4) (Fig. 1) ,,4mm (1/6 ) (Fig. 2) (Fig. 1) Guide adjusting screw Guide (Fig. 3) (Fig. 4) Foided edge 16 SEWING EMBROIDERY Presser foot darning plate Pattern selector ( ) or zig zag Raise and take off the foot. Place the fabric in embroidery hoop. Place darning plate over needle plate (see below). Lower the presser foot lifter. Hold the embroidery hoop firmly with your hand. While sewing the desired pattern, move the embroidery hoop slowly and do not allow your fingers to get near the needle. *Set the needle thread tension a little looser so that the bobbin thread is not pulled through to the right side of fabric. (See page 13). *It is recommended to mark the required embroidery pattern , on the right side of the fabric with a pencil or tailor s chalk. DARNING PLATE There are a few times when you want to control the feeding of the fabric yourself. Raise needle to its highest position and raise presser foot. Place darning plate over needle plate aligning two pins of darning plate with holes of needle plate. You may then determine the movement of the fabric yourself. See above for embroidery. Thread Shank BUTTONS Sew-through buttons on coats and hank to he fabric. machine Model 377 Model 373/37 Model 374 button foot Pattern selector Presser foot 1-5(54321) 4-6( button foot shank. and en the needle. wind 1. Align two holes of button with slot of presser foot and lower foot to hold the button securely. 2. Turn hand wheel manually until needle point is just above button. 3. Adjust stitch selector so needle enters right hole of button. 4. Turn hand wheel by hand so needle enters second hole. The stitch selector may need to be adjusted again. Stitch a number of times. NOTE: You may find it helpful to use transparent tape to position your button and to keep it in place during sewi...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: