Войти:
Оценок - 2, средний балл: 4.5 ( )

Инструкция по эксплуатации Sears, модель KENMORE 385. 17928

Производитель: Sears
Размер: 8.58 mb
Название файла: bcb7c979-310c-4f6c-99fa-620856dec5d5.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


foot GF ressure To raise the feed dogs, push (_) For dropping the feed dogs, the lever in the direction of push the lever in the direction dial: 0 Drop feed lever the arrow as illustrated. of the arrow as illustrated. Then turn the handwheel. * Feed dogs must always be up for normal sewing. 1 Drop the feed dogs. 2. Stretch the fabric with the hole in the center between embroidery hoops, as shown. 3. Lower the presser bar and sew a_ a siow speed. 4. Move the fabric bzick and forth slowly until you have covered the darning area. 5. Turn the fabric 1/4 turn and sew another layer of stitching over the first layer. NOTE: If your fabric is thin or badly damaged use a separate piece of fabric under the hole to reinforce it. 6. When you finish darning, return the pressure dial to 3. • Topstitching Set the Machine Stitch width control 0 f 1 213 4 Top thread tension Stitch length control 2 to 6 control red zone Here's How 1. Lower the presser foot. 2. Keep the edge of the fabric next to the right edge of the presser foot. 3. Guide the fabric evenly along this edge to produce an even row of topstitching 5/8" from the edge. I ! A: Zigzag foot Stretch Stitch L 1 _,. H: Straight foot The Stitch and Its Uses Topstitching emphasizes the lines of your garment and keeps seams and edges flat and crisp. Accent suits or blouses with one or two rows of topstitching around the outer edges of cuffs, lapels or collars. • Sew in a Zipper Fabric Preparation: Put the top sides of the fabric together and sew to the end of the zipper opening. Use the reverse to lock the stitches. Sew the zipper opening with stitch Set the LU Machine Stitch width control 0 1 2|3_4 / Zipp'er teeth Zipper tape 1 ] length at "4" and top thread tension at "3". Top thread tension control 2 to 6 Stitch length control 2 \\ End of opening To 1. Sew: Reset stitch length at 2 and top 4. Attach the pins on the presser bar zipper foot. to the right thread tension at 2 to 6. 5. Lower the zipper foot on the top Fold back the left seam allowance side at the bottom of the zipper Stretch Stitch as shown. so that the needle pierces the fold 2. Turn under the right seam allow-and the zipper tape. 6. Sew through the fold and the Top edge of fabric E: Zipper foot J 3. ance to form a 1/8" fold.Place the zipper teeth next to the zipper tape to the point where the J 1/8" fold and pin in place. slider begins. To attach the zipper foot: 7. Lower the needle to hold the fabric and raise the presser foot. I__._ " ,,1.,,_ _"_ • To sew on the left side of the zipper, attach the presser bar to the right pins on the zipper foot. L _'Thep right hand side_Jin°nthe I_ _ The pin on the • To sew on the right side of the zipper, _'_'_'_'_'_'_'_'__I_1 left hand side attach the presser bar to the left pins _ ,,i,,_l_ on the zipper foot. / J Top sideof fabric of fabric Top side To side "_ of fabric "_'_ "'-" of fabric J 8. Openthezipper. 10. Close the zipper and turn the Remove the zipper foot and 14. Stop about 2" from the top of the 9. Lowerthepresserfootandstitch therestoftheseam. fabric top side up. attach the pins on the presser zipper bar foot. to the left 15. zipper. Lower the needle into the fabric 12. Stitch across and below the botand raise the presser foot. tom of the zippel. 16. Remove the basting stitches and 13. Turn the corner and continue to open the zipper. guide the foot along the zipper 17. Lower the foot and stitch the teeth, as shown. rest of the seam. Make sure the Stitch through the fabric and fold is even. zipper tape. • Basic Zigzag Stitch width control 1to 5 Set the Machine Y Top tnread tension Stitch length J control 3 to 8 control red zone J 2 Here's How There are many ways to sew a zigzag stitch. IL))' Consult the specific variations for Stretch Stitch A: Zigzag foot The Stitch and Its Uses The zigzag stitch is one of the most common and most versatile stitches on your machine. It can be a utility stitch for sewing buttons, buttonholes, hemming, overcasting, mending and darn ing. It can also be used to decorate with trims, appliques and cut-out work or as a decorative stitch. detailed directions. Satin Stitch page 3_7, Applique Work page 3_88, Bar Tacking page 3__88, Monogramming page 3__66, Embroidery page 3__99, Button Sewing page 4___00, Overcasting page 41. Monogramming Stitch width l! os Top thread tension control 2 to 6 Stitch length control 0.5 to 1 \ Here's How 1. 2. Stretch Stitch r3. F: Satin stitch foot 4. 5. Set the same as satin stitch. Back the fabric with interfacing. Draw the letters on wtu, t_,=u, _ chalk. Satin stitch, adjusting width as necessary to pattern. If using paper, carefully when you have finished paper or the fabric the stitch form each remove it sewing. Satin Stitch Set the Machine Zigzag width: Stitch width Close to 0 control 2 to 5 1 2|3_4 II) 2 Top thread tension Stitch control 3 to 8 Stitch length length: control 0.5 to 1 3 > > > L L //// / Stretch Stitch F: Satin stitch foot _iii. _, •_...... Pressure dial 1 or2 L SI ,, I 1 The Stit...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории