Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
Caution: Make certain the POWER SWITCH is in the off position before inserting the batteries. 2. Insert (4)AA batteries in the battery slot compartment in the bottom of the machine. Be certain the batteries are in the correct polarities as marked on the machine. Then replace the battery compartment cover. 4 Threading the machine Threading the machine 1. Raise thread spindle (C) by grasping the exposed top and pulling upward until thread spindle (C) is fully extended. 2. Place thread spool (E) on the thread spindle (C) as shown. 3. Pull thread from the thread spool (E) on the thread spindle (C) and put it through the thread holder (1) in the direction toward front of machine. 4. Bring thread across to the thread tension screw (2). Thread goes over the tension adjusting screw and must be positioned between the two washers behind the tension adjusting screw(Q). This is what provides the lockstitch tension to the thread. 5. Pull thread from tension adjusting screw (Q) guide through thread take up lever (D) in the direction toward front of machine (3). 6. Pull thread through thread guide (4) inserting in the direction toward the front of the machine. 7. Pull thread down to thread guide (5) and insert thread from the top downward. If necessary, lower the needle (R) to reach this guide by turning the hand wheel (K) slightly counter-clockwise (in the direction toward you) to lower the needle (R). 8. Raise the needle (R) to reach the eye by turning the hand wheel (K) slightly clockwise (in the direction away from you). Insert thread through eye (6) of the needle from the front toward the back of the machine (use threader accessory if necessary). 9. Raise the Presser Foot (F) by lifting up on the lever at the rear of machine (G). 10.Pull about 10 inches of thread through the needle (R) and lay it on the deck under the presser foot (F) running in the direction away from you. 1 2 3 4 5 6 Threading main unit using side bobbin (Follow steps 4-10 with these exceptions.) 1. Pull bobbin spindle (U) out from main unit. 2. Insert bobbin spindle (U) through center hole of threaded bobbin. 3. Insert bobbin spindle (U) (with bobbin attached) into bobbin holder (V). Make sure bobbin spindle (U) with bobbin are tightly secured to main unit. Note: thread main unit with side bobbin simultaneously with thread spool for a double stitch method. Side bobbin is to be used only if you’re using this particular method of stitching. 5 Bobbin Winding and Insertion Winding the bobbin You can wind your own bobbins with thread from spools you purchase separately to have a virtually unlimited thread color selection. Match your fabrics or contrast with the thread shades of your choice. 1. Always remove the bobbin (S) from the bobbin case on the machine before you wind a new bobbin. 2. Place the thread spool (E) on the thread spindle (C). 3. Press down the bobbin winder handler (W), the bobbin winder (T) will be lifted up. 4. Take an empty bobbin. Pull the thread down from the thread (E) through the clamper (I) and thread the loose end through the small hole the bobbin to allow the small hole on the bobbin rim from the outside. 5. Leaving the loose end on the outside of the bobbin, wind the thread several turns around the INSIDE of the bobbin. 6. Place the bobbin on the bobbin winder spindle; making certain that the thread is winding onto the bobbin in a counter-clockwise direction. Adjust the bobbin to allow the small hole on the bobbin rim to line up with the spring on the bobbin winder spindle. 7. Press down the “ON” switch, the machine will start to wind the bobbin. 8. When the bobbin is full, switch off the machine. Insert the bobbin into bobbin case. 9. Lift up the bobbin winder handler. Bottom bobbin placement 1. Press the release button (H) on the rear of the machine to pop up the cover of the bobbin compartment (I). 2. Remove cover by lifting up where it has popped up at rear. 3. Place the bobbin with thread of your choice in the bobbin holder (J) leaving about 5 inches of thread extended out from the bobbin holder (J). 4. Lower presser foot (F). 5. Turn hand wheel (K) counter-clockwise (toward you). Needle (R) will go down, picking up the bobbin thread. Turn handwheel (K) until needle (R) has descended completely and then come up again to its highest raised point. Stop when needle (R) starts to go down again. 6. Raise the presser foot (F) and bring the spool thread around to the front. Pull the two threads toward the rear (away from you) and lay them under the presser foot (F). 7. Snap the bobbin compartment (I) cover down and into place. Note: Both the top and bobbin thread must be threaded correctly or the machine will not stitch properly. The machine may have come pre-threaded from the factory. Look at this threading carefully before removing it to replace the thread or bobbin with different thread. Then follow the preceding instructions to rethread. 6 Operating the Sew E-Z Rotate the handwheel to bring the needle to the highest positi...
Эта инструкция также подходит к моделям:Швейные машинки - SEW E-Z W338 (395.37 kb)