Оценок - 4, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
4 Bobbin .................................................... 5, 6, 7 Threading-Top Thread ............. ........................ 8 Using the Controls Top Tension Control ................................. 9, 10 Bobbin Tension Adjusting .............................. 11 Checking Tensions ....................................... 12 Stitch Length Control ................................... 13 Stitch Width Control .................................... 14 Reverse Stitch Control .................................. 15 Special Stitch Variegator ....................... ........ 15 Special Stitch Dial .................................. 16a, b Pressure Regulator .... . .................................. 17 Feed Dog Control ........................................ 18 Sewing Light ........... . .................................. 18 Seam Guide ................................................ 19 Accessories Needles ..................................................... 20 Needle, Thread, Fabric Chart .......................... 21 Presser Feet ................................................ 22 Section ]] Starting to Sew ........................................ 1 Garment Construction Stitches Straight Stitching ....................................... 2, 3 Zigzag Stitching .......................................... 4 Overcasting ................................................ 4 Stretch Stitching ......................................... 5 Special Finishing Stitches Blind Hemming. .......................................... 6 Satin Stitching ............................................ 7 Mending .................................................... 7 Appliqueing ................................... :............ 8 Buttonholing ........................................... 9, 10 ButtonSewing, Bar Tacking ........................... 11 Maxi Stitch Stretch ...................................... 11 Feather Stretch ........................................... 12 Darning, Writing and Monogramming .............. 13 Zipper Application ........................................ 14 Section ]]] Checking Performance Problems Section IV"Caring For The Machine Cleaning Feed Dogs and Shuttle ..................... 1 Oiling Under Arm Cover Plate and in Face Cover Plate ................................. 2 Oiling Underside .......................................... 2 Parts List.................................................. 3, 4 Knowing Your ewing Machine 1. Hand Hole Cover Plate 2. Seam Guide Lines 3. Presser Foot 4. Needle Clamp Screw 5. Presser Foot Screw 6. Thread Guide 7. Face Cover Thread Guide 8. Top Thread Tension Control 9. Face Cover Plate 10. Take-up Lever 11. Upper Thread Guide 12. Special Stitch Dial (Model 1250 only) 13, Stitch Width Control 14. Special Stitch Variegator (Models 1240, 1250 only) 15. Stitch Length and Reverse Stitch Control 16. Light and Power Switch 17. Feed Dog Control 18. Nomenclature Plate !!i_ii_iiiiiiii ii!!iii_ii!ii!iii,liiiiiiiiiiii!i_i 19. Clutch Knob 24. Pressure Regulator 20. Hand Wheel 25. Presser Foot Lever 21, Bobbin Winder 26. Thread Cutter 22. Thread Spool Pins 27. Feed Dogs 23. Bobbin Winder Tension Disc INSTALLING MACHINE O O O . Loosen the two hinge screws under 5. Plug the speed control cord into any holes in the rear edge of the machine 110-120 volt wall outlet. bed. 6. Turn on power by pushing light and 2. Raise hinge pins in the cabinet cutout. power switch. 3. Slip machine head onto the pins and 7. _Screw spool pins firmly in place with tighten hinge screws securely. screwdriver. Place the plastic spool 4. Push the speed control plug onto holder onto the spool pin. Holder and three-prong connector under the bed pins are packed in the accessory box. plate. Lower machine head to front cabinet flap. REMOVING BOBBIN CASE FROM SHUTTLE •/ iilE• • .• •.... •i•-if!••_• i 1. Turn hand wheel to raise needle to 3. Pull bobbin case straight out of its highest position. Lift hand hole shuttle. cover plate. To thread the bobbin case, see page 7. 2. Pull open latch of bobbin case. WINDING THE BOBBIN • • k k -k , Release clutch by turning clutch knob toward you. 2. Draw thread from spool through bobbin winder tension discs as shown. 3. Pull end of thread through hole in bobbin as shown. 4. Place bobbin onto bobbin winder shaft with end of thread coming from the top of the bobbin. Push bobbin winder latch against bobbin until it clicks. Holding onto end of thread, start machine. When bobbin is slightly filled, snip off end of thread. 5. Start machine. Wind thread until bobbin winder latch releases. 6. Tighten clutch knob and remove bobbin. Two spool pins have been included with this machine to aid in bobbin winding. By placing a spool of thread on the second spool pin, you may wind your bobbin without unthreading the machine. THREADING THE BOBBIN CASE o . Insert bobbin into bobbin case making sure thread is coming from bobbin as shown. , Pull thread through slot of case as shown. o 3. Pull thread under tension spri...
Эта инструкция также подходит к моделям:Швейные машинки - 1240 (4.92 mb)
Швейные машинки - 1250 (4.92 mb)