Оценок - 5, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Keep away from direct sunlight and heaters. Operate the mixer only after becoming familiar with its functions. Do not permit operation by persons not qualified for operating the mixer. Most damages are the result of unprofessional operation! Never use spray cleaners to clean the faders! Never use solvents or abrasive detergents to clean the mixer! It is recommended that you use a soft damp cloth. Please consider that unauthorized modifications on the device are forbidden due to safety reasons! Connections (Refer to diagrams on pages 3 & 4) • Make sure that the power switch (1) is set to OFF. Before connecting other devices to the mixer, all units have to be switched off and the Master Control (11) set to min. • Make sure that the available voltage is the correct voltage (10 Volts) before connecting to power. • In order to obtain the highest sound quality, use high quality American DJ® Ameri-Cable™ cables for connecting devices. Make sure that the cables are properly fixed. • Connect your amplifier to the OUT AMP jacks (16). • For recording, connect your tape recorder or cassette deck to the OUTPUT REC jacks (15). The REC OUT level will not be influenced by the Master Control (11). • Connect your microphone to the Microphone Input (10). (See diagram) • Connect your turntable(s) to the PHONO 1 jacks (13) or the PHONO 2 jacks (14) on the rear panel. You can only control the record player signal after switching the PHONO/LINE switches (2) to phono. The signal is then controlled via the CH-1 and CH-2 faders (3). • Connect your tape recorder, tuner, sound effects, CD player, cassette deck or any other line signals to the PHONO/LINE jacks (13 & 14) on the rear panel. You can only control the line signals after switching the PHONO/LINE switches (2) to LINE. The signal is then controlled via the CH-1 and CH-2 faders (3). © American DJ® AUDIO Los Angeles, CA 90058 USA Specifications subject to change without notice. XDM-241 User Instructions page 2 Functions CUE ch1 ch2 0 5 10 DJ MIC 0 5 10 CUE LEVEL 0 5 10 MASTER PHONO 1 LINE 1 LINE 2 PHONO 2 LINE 3 LINE 4 POWER ch1 PHONESMIC PROformer Series XDM-241 PREAMP MIXER SHREDDERSCRATCH MIXER L RdB +5 0 -5 -10 -15 +5 0 -5 -10 -15 ch2 CROSS FADER FEATHER FADER 1 8 7 9 11 2 2 5 10 4 3 3 ® 6 (1) POWER SWITCH (2) LINE/PHONO SWITCH - Used to select the input (LINE or PHONO) to be sent to channel 1 or 2. Can also be used for TRANSFORMER SCRATCHING. (3) CHANNEL FADER CHANNEL 1 / CHANNEL 2 - Used to adjust the input level of each channel. (4) CROSSFADER - Mixes the signals of channel 1 and channel 2. When the crossfader is set in the center position, both channels can be heard at once. (5) CUE LEVEL CONTROL - Adjusts the headphone output level. (6) CUE SWITCH DIAL CHANNEL 1 / CHANNEL 2 - Use the cue switch dial in order to select the channel to be monitored. (7) PHONES JACK - Connect headphones to this jack. Headphones from 8 Ohms to 600 Ohms can be used. 16 Ohms is recommended. (8) MASTER LEVEL DISPLAY -This display shows the signal level of the master output. (9) DJ MIC CONTROL - Adjusts the microphone volume. (10) MIC INPUT - 1/4 inch (6.3 mm) jack plug for microphone input to mixer. (11) MASTER LEVEL KNOB - Adjusts the level of the master output. © American DJ® AUDIO Los Angeles, CA 90058 USA Specifications subject to change without notice. XDM-241 User Instructions page 3 Inputs and Outputs LINE 1 CH 1 PHONO 1LINE 2 LINE 4LINE 4 LINE 3LINE 3 CH 2 PHONO 2AMP OUTPUT REC L - R -17 18 12 14 1316 15 (12) DC POWER IN (13), (14) LINE / PHONO INPUT JACK - Input jacks for CH1 & CH2. Connect turntables equipped with MM pickup cartridges to the PHONO input. CD Players or Tape Decks should be connected to the LINE input. Line level musical instruments with stereo outputs such as Rhythm Machines or Samplers should also be connected to the LINE inputs. (15) REC OUT - To record your record unit. The REC OUT level is not influenced by the master control. (16) AMP OUTPUT - Parallel output for P.A. output. Connect with the input of power amplifier. (17) GND (Ground Terminal) - Connect this terminal to ground lead of the turntable. This helps to reduce humming and popping noises. (18) LINE/PHONO SELECTOR - Used to switch the channel input jacks to line or phono. © American DJ® AUDIO Los Angeles, CA 90058 USA Specifications subject to change without notice. XDM-241 User Instructions page 4 Replacing the Crossfader Instructions for replacing the crossfader: • Disconnect from main power supply • Remove the fader knob. • Remove the two outer screws. • Take the fader out and unplug the connection cable. • Connect the new fader and replace back into mixer. IMPORTANT! • Only replace cross fader with American DJ® high quality Feather Fader™ (FF-1). Technical Specifications - model XDM-241 Inputs: Microphone 1.5mV, 600 Ohm Phono 3mV, 47kOhm Line 150mV, 27kOhm Output 7V, peak to peak Frequency range 20Hz-20KHz, ± 2dB Distortion <0.08% S/N-ratio >70dB Tone control Treble: 10Khz ± 12dB Bass: 100 Hz ± 12dB H...