Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
• Turn off all controls before unplugging. • Do not use appliance in an enclosed space where flammable, explosive or toxic vapors are given off by oil base paint, paint thinner, some mothproofing substances, or in an area where flammable dust is present. CAUTION This appliance must be connected to a grounded metal, permanent wiring system; or an equipment- grounding conductor must be run with the circuit conductors and connected to the equipment- grounding terminal or lead on the appliance. ALWAYS UNPLUG THE MACHINE BEFORE INSTALLING OR REMOVING ACCESSORIES. ALWAYS WEAR SHOES WHEN USING ELECTRICAL EQUIPMENT. SAVE THESE INSTRUCTIONS 2 ENGLISH Warranty ORECK MANUFACTURING COMPANY: (Oreck 21180 Johnson Road; Long Beach, MS, USA 39560 gives you the following warranty for this product only if it was originally purchased for use, not resale from Oreck or an Oreck Authorized Retail Dealer.) Oreck will repair or replace, free of charge, to the original purchaser, any part that is found to be defective in material or workmanship within one (1) year of the date of purchase. ORB555MC models carry a (5) five year limited motor warranty which applies to residential use. Note: If the unit is used commercially, a (1) one year overall warranty applies. Brushes, pads, drive blocks and other parts are subject to normal wear and are not covered by this warranty. This warranty does not apply to any part subjected to accident, abuse, alteration, misuse, damage caused by act of God, the use of voltages other than indicated on the serial number displayed on this product or service of this product by other than Oreck or a participating Factory Authorized Service Center. Oreck does not authorize any person or representative to assume or grant any other warranty obligation with the sale of this product. Oreck’s warranty is valid only if you retain proof of purchase from Oreck or an Oreck Authorized Retail Dealer for this product. If you purchase this product from any other source, your purchase is “AS IS,” which means Oreck grants you no warranty, and that you, not Oreck, assume the entire risk of the quality and performance of this product, including the entire cost of any necessary servicing or repairs of any defects. This warranty is in addition to your statutory and other legal rights. Operating Instructions The Orbiter® is the most advanced, easiest to use machine of its kind. With proper care and use, your Orbiter will last a lifetime. This booklet will tell you how to care for the Orbiter and all about its features, accessories and their use. Your Orbiter floor machine comes completely assembled and ready to operate once the Drive Pad Holder or Brush is attached. The off/on switch has international symbols (O) OFF and ( l ) ON. CAUTION: NEVER WORK ON THE MACHINE WHILE IT IS PLUGGED IN - ALWAYS DISCONNECT it from the electrical outlet. When leaving machine unattended, be sure to disconnect it. To Replace the Fuse: When changing fuse, replace with the same size fuse. To Attach Drive Pad Holder or Brush: Lay the floor machine on its back with the handle lying on the floor. This exposes the brush holder pan. Place the brush or drive pad holder over the round brush holder pan making sure it is in place. CAUTION: NEVER put the brush or pad holder on the machine by placing it on the floor and moving the running machine over it, or by placing the machine over the brush or pad holder and then starting the motor. To Remove Brush: Lay machine on its back and pull brush or pad holder off the round holder pan. To Use Machine: The Orbiter's on-off switch is located on the handle. It has been designed to be conveniently activated. On (I) - Off(O) is printed on the switch. BE CAREFUL that the switch is in the OFF (O) position before you plug the electric cord into the outlet. Before turning the machine on, be sure there is a pad or brush in place on the machine. ON/OFF SWITCH To Guide the Floor Machine: Grasp the unique “T” handle and glide the machine across the floor in a back and forth motion. The patented “T” handle feature gives you complete control. The Orbiter's perfectly balanced counter-weight system gives smooth and easy action with fingertip control. IMPORTANT - Always wear shoes when using your Orbiter. Before completing any of the following procedures for the first time, test a small hidden area. Care of your Oreck Floor Machine: This is a precision machine. Dropping, unreasonable bumping or rough handling may result in damage to the balanced counter-weight system. Wrap your cord loosely around the two hooks on the handle. Remove brushes after use. The bristles may be damaged due to the weight of the machine. Store your machine in the upright position. After each use, remove wax or cleaning solutions. After sanding, blow sawdust off motor. Clean housing and bumper with damp cloth after each use. A little care will keep your Orbiter looking like new. USER MAINTENANCE: Lubrication: The Orbiter motor bearings are factory lubricated...
Эта инструкция также подходит к моделям:Шлифовальные станки - Orbiter Multi-Purpose Floor Machine ORB555MC Series (398.25 kb)