Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
LEX 2 185/. Instruction manualEccentric sander Page 2 - 6 IMPORTANT: Read and understand all instructionsbefore using. Guide d.utilisationPonceuse excentrique Page 7 - 11 IMPORTANT: Lire et comprendre toutes lesinstructions avant de demarrer les travaux. Manual de instruccionesLijadora excentrica Pagina 12 - 16 IMPORTANTE: Lea y comprende todas lasinstrucciones antes de usar. 464 111_00 . GENERAL SAFETY RULE. instructions. Failure to follow all instructionsRead and understand al. listed below may result in electric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTION. Work area . Keep your work area clean and well lit. Cluttered benches and dark areas inviteaccidents. . Keep bystanders, children, and visitorsaway while operating a tool. Distractions ca. cause you to lose control. Personal safety . Stay alert, watch what you are doingand use common sense when operating atool. Do not use while tired or under theinfluence of drugs, alcohol, or medication. A moment of inattention while operating toolsmay result in serious personal injury. . Dress properly. Do not wear looseclothing or jewelry. Contain long hair. Keepyour hair, clothing, and gloves away frommoving parts. Loose clothes, jewellery, or longhair can get caught in moving parts. . Avoid accidental starts. Beforeconnecting the air supply make sure thatthe tool is switched off. Carrying tools withyour finger on the switch or plugging in toolsthat have the switch on invites accidents. . Remove adjusting keys or tools beforeturning the tool on. A wrench or key that is leftattached to a rotating part of the tool may resultin personal injury. . Do not overreach. Stand on both feetand keep proper footing and balance at alltimes. Proper footing and balance enables bettercontrol of the tool in unexpected situations. . Use safety equipment. Always wear eyeprotection. Dust mask, non-skid safety shoes,hard hat, or hearing protection must be used forappropriate conditions. Tool use and care . Do not abuse the hose. Never carry orpull the tool by the hose. Keep hose awayfrom heat, sharp edges or moving parts.Replace damaged hoses immediately. Damaged hoses increase the risk of accidents. 10 Use clamps or other suitable means tosecure and support the workpiece to astable platform. Holding the work by hand oragainst your body is unstable and may lead toloss of control. 11 Do not force tool. Use the correct toolfor your application. The correct tool will dothe job better and safer at the rate for which it isdesigned. 12 Do not use tool if switch does not turnit on or off. Any tool that cannot be controlledwith the switch is dangerous and must berepaired. 13 Disconnect the compressed-air hosefrom the tool before making anyadjustments, changing accessories, orstoring the tool. Such preventive safetymeasures reduce the risk of starting the toolaccidentally. 14Store idle tools out of reach of childrenand other untrained persons. Tools aredangerous in the hands of untrained users. 15 Maintain tools with care. Keep cuttingtools sharp and clean. Properly maintainedtools with sharp cutting edges are less likely tobind and are easier to control. 16 Check for misalignment or binding ofmoving parts, breakage of parts, and anyother condition that may affect the tool.soperation. If damaged, have the toolserviced before using. Many accidents arecaused by poorly maintained tools. 17Use only accessories that arerecommended by the manufacturer for yourmodel. Accessories that may be suitable for onetool may become hazardous when used onanother tool. Service18 Tool service may be performed only byqualified repair personnel. Service ormaintenance performed by unqualified personnelcould result in a risk of injury. 19 When servicing a tool, use only identicalreplacement parts. Follow instructions inthe Maintenance section of this manual. Useof unauthorized parts or failure to follow theMaintenance instructions may create a risk ofinjury. Various dust created by power sanding, sawing,Various dust created by power sanding, sawing,grinding, drilling and other construction activitiescontains chemicals known (to the State ofCalifornia) to cause cancer, birth defects or otherreproductive harm. Some examples of thesechemicals are: .lead from lead-based paints,.crystalline silica from bricks and cement and other masonry products, an. Technical data Sanding pad diameter. - LEX 2 15. - LEX 2 18. Driv. Operating pressure (flow pressure. No load spee. Orbits per minuteSanding stroke. - LEX 2 150/. - LEX 2 150/7, LEX 2 185/. Air consumption at nominal loadWeight. - LEX 2 15. - LEX 2 18. Symbols n. no load speed (revolutions. rp. revolutions per minut. op. orbits per minut. Use for intended purpose As specified, the machines are designed forsanding wood, plastic, metal, stone, composite,paintwork, filler and similar materials. Materialcontaining asbestos must not be processed withthese tools. The user is liable for any damageand injury resulting from incorrect usage. Functional descriptio....
Эта инструкция также подходит к моделям:Шлифовальные станки - LEX 2 185/7 (3 mb)
Шлифовальные станки - LEX 2 150/7 (3 mb)