Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
9. Always wear goggles or safety glasses when hammering, grinding, or drilling metal parts. 10. If the assembly calls for welding or cutting, be sure that there are no flammable materials close at hand and that bystanders have taken necessary precautions. Figure 5-1 AFTER COMPLETING ANY ASSEMBLY STEP, THOROUGHLY READ THE NEXT STEP IN THE ASSEMBLY INSTRUCTIONS BEFORE PROCEEDING WITH THAT STEP. 11. After completing assembly, thoroughly inspect the machine to be sure that all nuts, bolts, hydraulic fittings or any other fastened assemblies have been thoroughly tightened. 12. After completing assembly, be sure that all safety locking devices or guards are in place. 13. Before operating the machine, thoroughly read the operation section of this manual. 14. Before operating the machine, read the maintenance section of this manual to be sure that any parts requiring lubrication such as gearboxes are full to avoid any possible damage. BEFORE OPERATING THE EQUIPMENT, IF YOU HAVE ANY QUESTIONS REGARDING THE PROPER ASSEMBLY OR OPERATION, CONTACT YOUR AUTHORIZED BUSH HOG DEALER OR REPRESENTATIVE. 5-1 BASE UNIT ASSEMBLY A. Attach lower lift links to deck assembly using 5/8 x 2-1/2 bolts, flatwashers, lockwashers, hex nuts and pivot bushings. (Figure 5-1) B. Install lift pins onto lower links, securing with 7/8” lockwashers and hex nuts. C. Attach mast halves to deck assembly using 1/2 x 1-1/2” bolts, lockwashers and hex nuts. D. Loosely attach two caster arms to the front of the mower deck using 5/8 x 3-1/2” bolts, l;ockwashers and hex nuts. Loosely attach the remaining two caster arms to the rear of the mower deck using 5/8 x 3-1/2” bolts, lockwashers and hex nuts in each caster arm. Attach mast supports to lugs at the rear of the mower deck using 1/2 x 1-1/4” bolts, lock- washers and hex nuts. Spacers Lower Link Caster Arm Gearbox Mast Support Flex Link Mast Half 17 E. Fasten mast supports and upper flex link to G. Install front roller by securing the right and left mast halves using 1/2 x 5” bolt,pivot tube and locknut. roller mounts to the deck in the holes provided by F. Place one long spacer on the caster stems using 3/8 x 1” carriage bolts, flatwashers and lock- and insert into caster arms. Place three long spacers washers. (Figure 5-2) Assemble roller, roller shaft, and two short spacers on the caster stem above the retaining pin and roll pin as shown. caster arms. this arrangement will give a cutting H. Fill gearbox with EP80W-90 gear oil until oil height of approximately 1-3/4” . Secure with lynch level is at check plug on side of gearbox housing. pin retainers. With weight of cutter resting on all four Allow time for oil to seep through bearings into lower wheels, ensure that cutter is level. Tighten all bolts housing. (Capacity is 1 quart) Replace solid fill plug on mounting brackets. with breather plug supplied in operator’s manual package. Figure 5-2 Front Roller Roller Mounts 3/8 x 1” Bolt, Lockwasher and Flatwasher Roller Shaft Roller Retaining Pin Roll Pin 18 SAFETY DECALS To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge. Contact your authorized Bush Hog dealer for more information. 82619 78608 50012615 82617 82618 60873 50012616 19 TORQUE SPECIFICATIONS Proper toque for American fasteners used on Bush Hog equipment. Recommended Torque in Foot Pounds (Newton Meters).* AMERICAN BOLT DIAMETER WRENCH (IN.) “B” AND SAE SAE SAE SIZE (IN.) “A” THREAD SIZE GRADE 2 GRADE 5 GRADE 8 7/16 1/4 - 2O UNC 6 (7) 8 (11) 12 (16) 7/16 1/4 - 28 UNF 6 (8) 10 (13) 14 (18) 1/2 5/16 - 18 UNC 11 (15) 17 (23) 25 (33) 1/2 5/16 - 24 UNF 13 (17) 19 (26) 27 (37) 9/16 3/8 - 16 UNC 20 (27) 31 (42) 44 (60) 9/16 3/8 - 24 UNF 23 (31) 35 (47) 49 (66) 5/8 7/16 - 14 UNC 32 (43) 49 (66) 70 (95) 5/8 7/16 - 20 UNF 36 (49) 55 (75) 78 (106) 3/4 1/2 - 13 UNC 49 (66) 76 (103) 106 (144) 3/4 1/2 - 20 UNF 55 (75) 85 (115) 120 (163) 7/8 9/16 - 12 UNC 70 (95) 109 (148) 153 (207) 7/8 9/16 - 18 UNF 79 (107) 122 (165) 172 (233) 15/16 5/8 - 11 UNC 97 (131) 150 (203) 212 (287) 15/16 5/8 - 18 UNF 110 (149) 170 (230) 240 (325) 1-1/8 3/4 - 10 UNC 144 (195) 266 (360) 376 (509) 1-1/8 3/4 - 16 UNF 192 (260) 297 (402) 420 (569) 1-5/16 7/8 - 9 UNC 166 (225) 430 (583) 606 (821) 1-5/16 7/8 - 14 UNF 184 (249) 474 (642) 668 (905) 1-1/2 1 - 8 UNC 250 (339) 644 (873) 909 (1232) 1-1/2 1 - 12 UNF 274 (371) 705 (955) 995 (1348) 1-1/2 1 - 14 UNF 280 (379) 721 (977) 1019 (1381) 1-11/16 1-1/8 - 7 UNC 354 (480) 795 (1077) 1288(1745) 1-11/16 1-1/8 - 12 UNF 397 (538) 890 (1206) 1444 (1957) 1-7/8 1-1/4 - 7 UNC 500 (678) 1120 (1518) 1817 (2462) 1-7/8 1-1/4 - 12 UNF 553 (749) 1241 (1682) 2013 (2728) 2-1/16 1-3/8 - 6 UNC 655 (887) 1470 (1992) 2382 (3228) 2-1/16 1-3/8 - 12 UNF 746 (1011) 1672 (2266) 2712 (3675) 2-1/4 1-1/2 - 6 UNC 870 (1179) 1950 (2642) 3161...
Эта инструкция также подходит к моделям:Шлифовальные станки - MP6 (678.01 kb)