Оценок - , средний балл:
(
)
)
Производитель: Craftsman
Размер: 947.3 kb
Название файла: L0311129.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
,1_ WARNING: Keep hands and fingers clear of moving sanding belt, front idler roller, and drive roller assembly. Failure to do so wilt result in serious personal injury. _IL WARNING: Do not let your fingers rest over the front or right edge of the sander. If the sanding belt were to run off, or if it were not properly adjusted, your fingers could come in contact with the moving sanding belt resulting in possible serious injury. HELPFUL TIPS • If the sanding belt slips or does not track while sanding, you may be applying too much pressure. When this occurs, remove the sander from the workpiece. If you properly adjust the belt tracking, the sanding belt wilt return to its normal and correct position on the drive roller and front roller. • Use a coarser sanding belt for heavy sanding, not heavy pressure. The weight of the tool is sufficient to provide adequate pressure at the correct location. • The front roller of the sander is not designed for contour sanding. Sanding on the front roller could cause irregularity in the sanding belt tracking. Fig. 10 14 ,_ WARNING: When servicing, use only identical Craftsman replacement parts. Use of any other part may create a hazard or cause product damage. ,_ WARNING: The belt sander should never be connected to a power supply when you are assembling parts, making adjustments, cleaning, performing maintenance, or when the tool is not in use. Disconnecting the tool prevents accidental starting that could cause serious injury. GENERAL Only the parts shown on the parts list are intended to be repaired or replaced by the customer. All other parts are an important part of the double insulation system and should be serviced only by a qualified Sears service technician. Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc. dt_ WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc. come in contact with plastic parts. They contain chemicals that can damage, weaken, or destroy plastic. Electric tools used on fiberglass material, wallboard, spackling compounds, or plaster are subject to accelerated wear and possible premature failure because the fiberglass chips and grindings are highly abrasive to bearings, brushes, commutators, etc. Consequently, we do not recommend using this tool for extended work on these types of materials. However, if you do work with any of these materials, it is extremely important to clean the tool using compressed air. _ WARNING: Always wear safety goggles or safety glasses with side shields during power tool operation or when blowing dust. If operation is dusty, also wear a dust mask. Failure to do so could result in possible serious injury. LUBRICATION All the bearings in this tool are lubricated with a sufficient amount of high grade lubricant for the life of the tool under normal operating conditions. Therefore, no further lubrication is required. 15 --CRAFTSMAN BELT SANDER -MODEL NUMBER 315.117260 - SEE NOTE 8 5 10 \ 3 14 9 4 Note: The assembly shown represents an important part of the double insulated system. To avoid the possibility of alteration or damage to the system, service should be performed by your nearest Sears repair center. Contact your nearest Sears retail store for service center information. 16 --CRAFTSMAN BELT SANDER -MODEL NUMBER 315.117260 -I The model number wilt be found on a plate attached to the motor housing. Always mention the model ! number in all correspondence regarding your BELT SANDER or when ordering repair parts. SEE BACK PAGE FOR PARTS ORDERING INSTRUCTIONS PARTS LIST Key Part No. No. Description Qty. 1 940211009 Logo Plate ............................................................................................................. 1 2 *** Sanding Belt .......................................................................................................... 1 3 300027035 Dust Collection Bag ............................................................................................... 1 4 690711001 Wear Plate ............................................................................................................. 1 5 590477001 Belt Cover .............................................................................................................. 1 6 660312001 * Screw (8-32 x 3/8 in.) **STD510803 ..................................................................... 2 7 940301004 Data Plate .............................................................................................................. 1 8 590560001 Belt ........................................................................................................................ 1 9 900720001 Backing Pad .......................................................................................................... 1 10 660272001 * Screw (M4 x 14 mm) .......