Оценок - 5, средний балл: 3.2
(
)
)
|
Фрагмент инструкции
Make sure car surfaces are completely dry before starting to polish the car. NOTE: Do not polish any car in direct sunlight or when the body is hot. 2. Apply Liquid Wax Apply a small amount of liquid wax to the foam pad. Do not start the polisher until the pad is in contact with the car body. Starting the tool without this contact will cause spraying of the wax. NOTE: Too much liquid wax is wasteful and yields no benefit. It is also difficult to remove. 3. Apply To Car Turn the polisher on and move it over the work surface with side to side and front to back strokes. Simply guide the tool. Any extra pressure you apply will only slow the tool and yield an inferior result. Place the cord in a location which will avoid entanglement in the rotating pad. Apply more liquid wax as required to produce a light, uniform film (will appear as small ringlets on the work surface). Apply the liquid wax to the entire car. 4. Remove The Wax – Polishing Allow the applied liquid to dry thoroughly before starting to remove it and buff the car. Replace the foam pad with the polishing bonnet and move the tool over the car starting at the top and then down the sides. Let the weight of the tool do the work on the horizontal surfaces and use light pressure on the sides and other vertical surfaces. It is recommended that the fine dry dust left after removing the dried wax be removed by hand with a dry soft cloth. Additional Information and Tips for Polishing • Older car finishes may become oxidized or damaged by air pollutants, particularly on horizontal surfaces such as roofs, hoods, etc. These surfaces may have to be polished twice to restore the finish. For severe damage, only a professional car detailer or reconditioner may be able to restore the finish. • Removing wax which is not completely dry or allowing dried wax dust to build up on the car may clog the bonnet. If this happens remove the bonnet and shake hard to remove dried wax dust. • The chemical action of the cleaners and waxes and the speed of the polisher will do the work for you. Applying heavy pressure on the tool is not recommended. • Do not use to polish glass, vinyl tops or convertible tops. • When you are finished buffing, remove the bonnet from the polisher and allow the pad to air dry. Never store the tool resting on the side of the pad. Cleaning Bonnets Wash bonnets thoroughly in a strong solution of detergent and warm water. Floor cleaning detergents work best. Do not use detergents such as hand cleaners that contain abrasives. Do not machine wash. Additional Information and Tips for Sanding • Always hold the tool with both hands (Fig. 9). Do not place your hands over the ventilation slots. • Do not exert too much pressure on the tool. • Regularly check the condition of the sanding sheet. Replace when necessary. • Always sand with the grain of the wood. • Use extra fine grit when sanding new layers of paint before applying another layer. • On very uneven surfaces, or when removing layers of paint, start with a coarse grit paper. On other surfaces start with a medium grit. In both cases, gradually change to a fine grit for a smooth finish. Accessories Recommended accessories for use with your tool are available at extra cost from your local dealer or authorized service center. If you need assistance in locating any accessory for your tool, please call 1-800-54-HOW-TO (544-6986). CAUTION: The use of any other accessory not recommended for use with this tool could be hazardous. IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts. Service Information Black & Decker offers a full network of company-owned and authorized service locations throughout North America. All Black & Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical advice, repair, or genuine factory replacement parts, contact the Black & Decker location nearest you. To find your local service location, refer to the yellow pages directory under "Tools—Electric" or call: 1-800-54-HOW-TO (544-6986). Full Two-Year Home Use Warranty Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material or workmanship. The defective product will be replaced or repaired at no charge in either of two ways. The first, which will result in exchanges only, is to return the product to the retailer from whom it was purchased (provided that the store is a participating retailer). Returns should be made within the time period of the retailer’s policy for exchanges (usually 30 to 90 days after the sale). Proof of purchase may be required. Please check with the retailer for their specific return policy regarding returns that are beyond the time set for exchanges. The second option is to take or send the product (prepaid) to a Black &...