Оценок - 5, средний балл: 4
(
)
)
|
Фрагмент инструкции
• Sanding should be done in a manner to reduce tracking of paint dust outside the work area. CLEANING AND DISPOSAL • All surfaces in the work area should be vacuumed and thoroughly cleaned daily for the duration of the sanding project. Vacuum filter bags should be changed frequently. • Plastic drop cloths should be gathered up and disposed of along with any dust chips or other removal debris. They should be placed in sealed refuse receptacles and disposed of through regular trash pick-up procedures. During clean up, children and pregnant women should be kept away from the immediate work area. • All toys, washable furniture and utensils used by children should be washed thoroughly before being used again. MOTOR Your Black & Decker tool is powered by a Black & Decker-built motor. Be sure your power supply agrees with nameplate marking. 120 Volts AC only means your tool will operate on standard 60 Hz household power. Do not operate AC tools on DC. A rating of 120 volts AC/DC means that you tool will operate on standard 60 Hz AC or DC power. This information is printed on the nameplate. Lower voltage will cause loss of power and can result in overheating. All Black & Decker tools are factory-tested; if this tool does not operate, check the power supply. Assembly/Adjustment Set-Up WARNING: Always unplug sander from power supply before any of the following operations. FS500 SANDER -ATTACHING SANDPAPER To operate the paper clamps on your sander, simply lift them up with your thumb, as shown in Figure 1. Rotate the clamp lever downward until the clamp is fully opened. Insert one short edge of the paper under the clamp. Push edge squarely up against the flat wall of the platen and close the paper clamp on that side. Wrap the sandpaper around to fit the other edge under the opposite paper clamp. Push as much paper under the second clamp as possible before securing the paper clamp. Any slack in the paper will reduce sanding performance. NOTE: The FS500 comes with the PAPER PUNCH shown in figure 2. The punch may be permanently attached to a workbench by screwing it down using the two holes provided. If it is on a work surface simply press the sander ( with sandpaper firmly attached ) down on the punch to create the dust collection holes. If it is hand held simply press the punch against the sander pad. FS1000 SANDER -ATTACHING HOOK AND LOOP SANDPAPER To attach the sandpaper, carefully center it over the sanding pad ensuring that the holes in the paper align with the holes in the pad and press the sandpaper firmly in place. The hook and loop fastening system sandpaper can be easily removed by simply pulling it off. Take care to grip only the paper when removing the sandpaper. It can be reused as desired. NOTE: When storing the sander for extended periods of time, place the pad on a flat surface. DETAIL SANDING Your tool is equipped with a base which allows you to use it on large flat surfaces and tight spots or corners. The sandpaper tips may wear unevenly, depending on use. They are designed to allow you to interchange and/or rotate the diamond tip. To rotate the sanding tip, remove the tip, rotate it 180 degrees, and press it back on the base. Note: Remove extra tips from sandpaper (Figure 3) before using product. These extra tips can be used later when the original tip wears out. Operating Instructions -FS500 & FS1000 WARNING: To reduce the risk of serious personal injury, read, understand and follow all important safety warnings and instructions prior to using this tool. SWITCH To turn the tool ON, hold it as shown in Fig. 4 and push the portion of the dust protected switch marked "I". To turn the tool OFF, push the portion of the switch marked "O". OPERATION Grasp the sander and turn it ON. Move it in long, sweeping strokes along the surface, letting it do the work. Utilize an even pressure across the sanding pad. Excessive pressure in the corner area may cause damage. Pushing down on the tool while sanding actually slows the removal rate and produces an inferior quality finish. Check your work often. These sanders are capable of removing material rapidly. DUST EXTRACTION WARNING: Collected sanding dust from sanding surface coatings (polyurethane, linseed oil, etc.) can self-ignite in sander dust bag or elsewhere and cause fire. To reduce risk, empty bag frequently and strictly follow sander manual and coating manufacturer's instructions. Your sander comes equipped with a cloth canister to collect the dust generated while sanding. To attach the canister onto the sander simply slide it firmly onto the dust extraction port at the back of the sander and twist it slightly. To empty the dust canister, remove it from the sander by simply twisting slightly and pulling it straight back. Dump the sanding debris into an appropriate trash receptacle. You may, if you prefer, attach a vacuum cleaner to the tool to collect the dust as you sand. Simply remove the dust bag, and install the vacuum hose. Ensure that the vacuum clean...