Оценок - 4, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Be sure switch is off when plugging in. 17 OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 18 STAY ALERT. Watch what you are doing Use common sense. Do not operate tool when you are tired. ' 19 CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this * instruction manual. Do noi use tool if switch does not turn it on and off. 20. DO NOT OPERATE portable electric tools near flammable liquids or in gaseous or n explosive atmospheres Motors in these tools normally spark, and the sparks might ignite fumes. 2 METAL GUIDE FIG. 8 HOLE PUNCHER STOP PAPER HOLDER SANDING It is not necessary to exert a lot of pressure on the tool when sanding horizontally. The weight of the sander itself is usually sufficient to ensure satisfactory results Any excess will reduce its efficiency. In order to obtain an optimum finish, it is essential to progressively reduce the grain size of the paper being used With each change in grain size, it is recommended to sand at right angles in relation to the previous sanding In order to obtain a perfect finish, after using a very fine-grained paper, we recommend wiping the work surface with a slightly damp rag and sanding again with the finest paper possible. In order to obtain maximum dust collection, it is important to empty the dust bag frequently. The rate at which the dust bag will fill up is largely dependent on the type of material being sanded and the size of grit used. A good rule of thumb is to empty the bag when it becomes about 1/3 full So that the recovery bag can be thoroughly cleaned, it is washable and must be 'dried before replacing in sander. TOOL CARE Keep your machine as clean as possible by wiping with a clean cloth and occasionally blowing through with air Avoid overloading your sander Overloading will result in a considerable reduction in speed and efficiency and the unit will become hot. In this event, run sander at a “no load” condition for a minute or two This may be accomplished by holding unit away from work surface and allowing it to run “free speed.” 7 SWITCH ■' ' To operate unit, press right side of rocker switch. A white mark should appear to indicate switch is in the “on” position. To stop unit, press left side of rocker switch. The white mark should no longer be visible. HOLE PUNCH OPERATION 1. Remove the metal guide and the hole-puncher from the paper holder . 2. Place the paper, grain upwards on the holder so that the paper As in contact with the • stop. 3. Place the metal guide above the paper so that it is correctly positioned in relation to the holder. 4. With the aid of the holepuncher, make holes by pressing firmly through the guide and the paper. 5. Take out the paper, checking that all the holes are clean and match the sander perfectly. 6. If the holepuncher, after a considerable period of use, produces poor holes, then it is essential to sharpen or replace it. 6 i DOUBLE INSULATION Your Sander is DOUBLE-INSULATED to give you added safety. This means that ft is con.structed throughout with TWO separate ’layers’* of electrical insulation or one DOUBLE thickness of insulation between you and the tool’s electrical system Tools built with this insulation system are not intended to be grounded As a result, your ’ Drill is equipped with a two-prong plug which permits you to use extension cords without concern for maintaining a ground connection. NOTE DOUBLE-INSULATION does not take the place of normal safety precautions when operating this tool. The insulation system is for added protection against injury resulting from a possible electrical insulation failure within the tool CAUTION. When servicing Double Insulated Tools USE ONLY IDENTICAL REPLACEMENT PARTS. Repair or replace damaged cords EXTENSION CORDS Double Insulated tools have 2 wire cords, and can be used with 2 wire or 3 wire extension cords. Only round jacketed extension cords should be used, and we recommend that they be listed by Underwriters Laboratories (U.L.) (C.S. A. In Canada) If the extension will be used out side, the cord must be suitable for outdoor use Any cord marked as outdoor can also be used for indoor work An extension cord must have adequate wire size (AWG or. American Wire Gauge) for safety, and to prevent loss of power and overheating. The smaller the gauge number of the wire, the greater the capacity of the cable, that is 16 gauge has more capacity than 18 gawge. When using more than one extension to make up the total length, be s...