Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
The pad tips may wear unevenly, depending on use. The pads are designed to allow you to interchange and /or rotate the diamond tip. Fitting Sanding Sheets ( Fig. 2) • Detach the two diamond-shaped tips from the sanding sheet. • Hold the tool with the sanding base facing upwards. • Place the sanding sheet onto the sanding base. The diamond-shaped tip can be reversed and replaced when worn. • When the front part of the tip is worn, detach it from the sheet, reverse it and press it onto the sanding base again. • When the whole tip is worn, remove it from the sanding base and fit a new tip. Tip of the Sanding Base ( Fig. 3) When the sanding base tip is worn, it can be reversed or replaced. • Reverse or replace the worn part. Finger Attachment ( Fig. 4) The finger attachment is used for fine detail sanding. • Remove the screw. • Remove the diamond-shaped tip holder from the sanding base. • Fit the finger attachment onto the sanding base. • Fit and tighten the screw. • Align the sanding sheet with the finger attachment. Contour Holder Attachment (Fig. 5) • The contour sanding pieces are for sanding curved surfaces and grooves. • Remove the screw. • Remove the diamond-shaped tip holder from the sanding base. • Fit the contour holder onto the sanding base. • Fit and tighten the screw. Fitting and Removing a Contour Piece (Fig. 6 & 7) • Choose the contour sanding piece profile most suitable for your application. • Place one end of the contour sanding piece into the recess at the front end of the contour holder. • Push the other end of the contour sanding piece until it clicks into place. • To remove the contour sanding piece, push it forward then pull the rear end out of the contour holder (fig. 7). Fitting a Sanding ( Fig. 8) • Align the sanding sheet with • Press the sanding sheet onto sure that the sanding sheet follows Maintenance Use only mild soap and damp cloth never immerse any part of the tool into IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by authorized organizations, always using identical replacement Accessories TM Look for the following Mouseaccessories at your local retailer. Catalog # Description Contents 74-583 120 Medium Sandpaper 5 sheets 74-584 180 Fine Sandpaper 5 sheets 74-585 220 Extra Fine Sandpaper 5 sheets 74-586 Sandpaper Assortment 1 sheet of 120 grit paper, 2 sheets each 180, 220 paper 74-587 Finger Attachment Paper 5 fingers each of 120, 180, 220 74-588 1 OT Power Wool 3 sheets 74-589 4 OT Power Wool 3 sheets 74-581 Polishing Kit 2 sheets of 1 OT power wool, 2 sheets of 4 OT power wool, 2 foam pads 74-582 Scrubbing Kit 2 coarse abrasive pads, 2 fine abrasive pads, 2 foam pads 74-580 Sanding/Polishing Kit 2 sheets of 1 OT power wool, 2 sheets of 180 grit sandpaper, 2 sheets of 240 grit sandpaper, 2 foam pads, 5 finger attachment paper 74-671 Universal Sandpaper/Coarse 5 sheets of 80 grit 74-672 Universal Sandpaper/Med. 5 sheets of 120 grit 74-673 Universal Sandpaper/Fine 5 sheets of 220 grit 74-674 Universal Sandpaper Assortment Recommended accessories for use with your tool are available at extra cost. Listings per retailer may vary. The hook and loop pad and individual bases are replaceable parts. If they become worn, contact your local service center. For more information call: 1-800-544-6986. WARNING: The use of any accessory not recommended for use with this tool could be hazardous. Application / Accessory Matrix ACCESSORY RECOMMENDED APPLICATIONS / USES MEDIUM GRIT SANDPAPER PAINT, VARNISH, RUST REMOVAL FINE GRIT SANDPAPER SURFACE BLENDING AND FINISHING EXTRA FINE GRIT SANDPAPER SANDING BETWEEN COATS OF PAINT OR VARNISH DETAIL SANDING TIPS CORNERS / HARD TO REACH PLACES 1 OT POLISHING / STRIPPING WOOL POLISHING METALS / STRIPPING VARNISH OR URETHANE 4 OT FINE POLISHING WOOL FINE POLISHING, SATIN FINISH ON PAINT / VARNISH / URETHANE GREY FOAM PAD APPLYING AND REMOVING POLISH WHITE NON- WOVEN PAD LIGHT SCRUBBING RED NON- WOVEN PAD HEAVY SCRUBBING / RUST REMOVAL The pads described above are available in kits where Mouse products are sold, The hook and loop pad and individual bases are replaceable parts. If they become worn, contact your local service center. For more information call 1-800-544-6986. 8 9 90518305 12/11/10:51 Problem • Zone lights do not workas intended. • Unit will not start. TROUBLESHOOTING Possible Cause • Voltage to tool isbelow 120 volts. • Cord not plugged in. • Circuit fuse is blown. • Circuit breaker is tripped. • Cord or switch is damaged. Possible Solution • Plug tool in outlet that isnot shared. • Re-calibrate tool (refer to calibrationsection in manual). • Use product as intended, lights willnot cause the tool to operate differently. • Red indicator will continue to warn against too much pressure. • Plug tool into a working outlet. • Replace circuit fuse. (If the product repeatedly causes the circuit fuse toblow, discontinue use immediatelyand have it serviced at a Black & Decker service center...