Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
Speed Preselection (GWS 6-100 E, GWS 6-115 E, GWS 8-100 CE, GWS 8-115 CE, GWS 8-125 CE) Preselect the required speed using the thumb wheel 1 according to the table following the section “Tool Specifications” (reference values). Operating Instructions Clamp the workpiece if it does not remain stationary due to its own weight. Do not strain the machine so heavily that it comes to a standstill. Grinding and cutting discs become very hot while working; do not touch until they have cooled. Rough Grinding The best roughing results are achieved when setting the machine at an angle of 30° to 40°. Move the machine back and forth with moderate pressure. In this manner, the workpiece will not become too hot, does not discolour and no grooves are formed. Never use a cutting disc for roughing. Flap Disc With the flap disc (accessory), curved surfaces and profiles (contour sanding) can be worked. Flap discs have a considerably higher service life than sanding sheets, lower noise level and lower sanding temperatures. Cutting When cutting, do not press, jam or oscillate the machine. Work with moderate feed, adapted to the material being machined. Do not reduce the speed of running down cutting discs by applying sideward pressure. The direction in which the cutting is performed is important. The machine must always work in an up-grinding motion. Therefore, never move the machine in the other direction! Otherwise, the danger exists of it being pushed uncontrolled out of the cut. When cutting profiles and square pipes, it is best to start with the smallest cross section. Rotating the Machine Head Before any work on the machine itself, pull the mains plug. The machine head can be rotated with respect to the machine housing in 90° steps. In this manner, the On/Off switch can be brought to an advantageous handling position for special working situations, e. g., for cutting work with the cutting guide/cutting grinder stand (accessory) or for left-handed persons. Unscrew completely the four screws. Rotate the machine head carefully and without removing from the housing to the new position. Screw in the screws again and tighten. Maintenance and Cleaning Before any work on the machine itself, pull the mains plug. . For safe and proper working, always keep the machine and the ventilation slots clean. In extreme working conditions, conductive dust can accumulate in the interior of the machine when working with metal. The protective insulation of the machine can be degraded. The use of a stationary extraction system is recommended in such cases as well as frequently blowing out the ventilation slots and installing a residual current device (RCD). 18 • 2 609 140 081 • TMS • 15.01.04 English - 6 2 609 140 081 - Buch Seite 7 Dienstag, 20. Januar 2004 8:52 08 2 609 140 081 - Buch Seite 7 Dienstag, 20. Januar 2004 8:52 08 If the machine should fail despite the care taken in manufacturing and testing procedures, repair should be carried out by an after-sales service centre for Bosch power tools. In all correspondence and spare parts orders, please always include the 10-digit order number given on the nameplate of the machine. WARNING! Important instructions for connecting a new 3-pin plug to the 2-wire cable. The wires in the cable are coloured according to the following code: strain relief live = brown neutral = blue To be fitted by qualified professional only Do not connect the blue or brown wire to the earth terminal of the plug. Important: If for any reason the moulded plug is removed from the cable of this machine, it must be disposed of safely. Environmental Protection Recycle raw materials instead of disposing as waste The machine, accessories and packaging should be sorted for en- vironmental-friendly recycling. These instructions are printed on recycled paper manufactured without chlorine. The plastic components are labelled for categorized recycling. Service and Customer Assistance Exploded views and information on spare parts can be found under: Great Britain Robert Bosch Ltd. (B.S.C.) P.O. Box 98 Broadwater Park North Orbital Road Denham-Uxbridge Middlesex UB 9 5HJ . Service............................ +44 (0) 18 95 / 83 87 82 . Advice line .................... +44 (0) 18 95 / 83 87 91 Fax............................................. +44 (0) 18 95 / 83 87 89 Ireland Beaver Distribution Ltd. Greenhills Road Tallaght-Dublin 24 . Service................................... +353 (0)1 / 414 9400 Fax.................................................... +353 (0)1 / 459 8030 Australia Robert Bosch Australia Ltd. RBAU/SPT2 1555 Centre Road P.O. Box 66 Clayton 3168 Clayton/Victoria . ............................................... +61 (0)1 / 800 804 777 Fax............................................... +61 (0)1 / 800 819 520 E-Mail: CustomerSupportSPT@au.bosch.com New Zealand Robert Bosch Limited 14-16 Constellation Drive Mairangi Bay Auckland New Zealand . ...............................................
Эта инструкция также подходит к моделям:Шлифовальные станки - GWS 6-100 (E) (1.77 mb)
Шлифовальные станки - GWS 6-115 (E) (1.77 mb)
Шлифовальные станки - GWS 8-100 C (CE) (1.77 mb)
Шлифовальные станки - GWS 8-125 C (CE) (1.77 mb)