Оценок - 5, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
To avoid injury from accidental contact with moving parts, don't do layout, assembly, or setup work on the sander while any parts are moving. AVOID ACCIDENTAL STARTING. Make sure switch is " OFF" before plugging sander into a power outlet. Plan your work. USE THE RIGHTTOOL. Don't force tool or attachment to do a job it was not designed to do. CAUTION: This machine is not designed for heavy deburring operations, When finishing metals, sparks or hot fragments could cause a fire. To avoid this, disconnect any dust collecting hose from the san der. Also, remove all traces of wood dust from inside dust traps in the sander. Dress for safety. Any power sander can throw foreign objects into the eyes. This can cause permanent eye damage. Wear safety goggles (not glasses) that comply with ANSI Z87.1. Everyday eyeglasses have only impact resistant lenses. They are not safety glasses. Safety goggles are available at Sears retail catalog stores. Glasses or goggles not in compliance with ANSI Z87,1 could seriously hurt you when they break. = Do not wear loose clothing, gloves, neckties or jewelry (rings, wrist watches). They can get caught and draw you into moving parts. • Wear nonslip footwear. ° Tie back long hair. o Roll long sleeves above the elbow. • Noise levels vary widely. To avoid possible hearing damage, wear ear plugs or muffs when using sander for hours at a time. ° Sanding operations are usually dusty. Wear a dust mask along with the safety goggles, Inspect your workplace. Make sure there are no nails or foreign objects in the part of the workpiece to be sanded. Plan your work to avoid THROWBACKS--when the work- piece catches on the sanding belt or disc and is torn fro m you r hands. • Make sure there's no debris between the workplace and its supports: ° When sanding irregularly shaped workpieces, plan your work support so it will not slip and be pulled from your hands. Use extra caution with large, very small or awkward work- pieces: • Never use this tool to finish pieces too small to hold by hand, • Use extra supports (tables, saw horses, blocks, etc.) for any workpieces large enough to tip when not held down to the table top. ,, NEVER use another person as a substitute for a table extension, or as additional support for a workpiece that is longer or wider than the basic sander table, or to help feed, sup port or pull the workpiece. o When finishing on the Disc, always press the workpiece against the "Down" side of the disc. Sanding against the side coming up from under the table could damage the work by making it "chatter;' or tear the work from your hands and throw it, • Sand only one workpiece at a time. • Clear everything except the workpiece and feinted support devices off the table before turning the sander on. 19 operaho " rt Plan the way you will hold the workpiece from start to finish Avoid awkward operations and hand positions Where a sudden s p cou dcause fingers or hand to move into a sanding surface, Keep fingers away from where the belt goes into the dust trap- DON'T OVERREACH, Keep good footing and balance, Keep your face and body to one side. out of line with a possible throwback. WHENEVER SANDER IS RUNNINGWARNING: Don't let familiarity (gained from frequent use of your belt and disc sander) cause a careless mistake. A care less fraction of a second is enough to cause a severe injury. Before starting your cut, watch the sander while it runs. if it makes an unfamiliar noise or vibratesa lot, stop immediately, Turn the sander off, Unplug the sander, Do not restart until finding and correcting the problem. Make sure the sanding disc turns counterclockwise before using the sunder, SURFACE FINISHING ON THE ABRASIVE BELT. FLATSURFACES Hold the work piece firmly with both hands, keeping fingers away from the abrasive belt. Keep the end butted against the backstop and move the work evenly across the abrasive belt. Use extra caution when finishing very thin pieces. For finishing long pieces, remove the backstop. Apply only enough pressure to allow the abrasive belt to remove material. If the abras=ve belt stalls and the belt pulleys slip while applying moderate pressure to the workpiece, the abrasive belt reouires more tension. END FINISHING ON THE ABRASIVE BELT, I1 is more convient to finish the ends of long work- pieces with the abrasive belt in a vertical position. Move the work evenly across the abrasive belt. For accuracy use a miter guage. The table may be tilted for beveled work. See Getting To Know Your Finishing Machine section for adjusting the abrasive belt table and the work table, KEEP CHILDREN AWAY. Keep aU visitors a safe distance from the sander. Make sure bystanaers are clear of the sunder and workpiece. DON'T FORCE TOOL. it will do the job better and safer at its designated rate. Press the workoiece against the sanding material only hard enough to let it sand without bogging down or binding. Before freeing any jammed material: • Turn switch "OFF," • Unplug the sanaer. • Wait for al...
Эта инструкция также подходит к моделям:Шлифовальные станки - 113.225900 (1.75 mb)
Шлифовальные станки - 113.225909 (1.75 mb)