Оценок - 4, средний балл: 4
(
)
)
|
Фрагмент инструкции
For this reason, always make sure that nobody is placed in any danger and that there are no inflammable materials near the working area. ■ Q Warning! noxious fumes! Any harmful / noxious dusts generated from sanding represent a risk to the health of the person operating the device and to anyone near the work area. UJwARNI nG|bUBThAbA03! When sanding wood and in particular when working on materials that give rise to dusts that are hazardous to health, the sander must be connected to a suitable external dust extraction device. AkA Wear protective glasses and a dust mask! ■ Ensure sufficient ventilation when working on plastics, paints, lacquers, etc. ■ Do not soak materials or surfaces to be worked with liquids containing solvents. ■ Avoid sanding of lead-based paints or other materials that are hazardous to health. ■ Material containing asbestos may not be worked on. Asbestos is considered a carcinogen. ■ The appliance is designed for dry surface sanding of wood, plastic, metal and smoothing compounds as well as painted surfaces. ■ Never work on moistened materials or wet surfaces. Water entering an electrical device increases the risk of electric shock. ■ Always hold the appliance firmly with two hands while working (see also Fig. D, E). ■ Never support your hands next to or in front of the device or on the surface being worked as there is a risk of injury in the event of slipping. ■ Always switch off the appliance and allow the sanding pad [9| to come to a stop before setting down the oscillating sander. ■ Always pull the power plug out of the socket for all work pauses, before any work on the appliance (e.g. changing the sanding paper) and when not in use. Ill PARKSIDE GB/IE 9 General safety advice for electrical power tools / Operation ■ The appliance must always be kept clean, dry and free of oil or lubricating greases. • Original ancillaries / and accessories ■ Only use accessories and tools that are specified in the operating instructions. The use of tools and accessories other than those recommended in the operating instructions could lead to an increased risk of personal injury for you. • Operation • Switching On and Off Switching on intermittent function: □ Press the ON / OFF switch |T. Switching off intermittent function: □ Release the ON / OFF switch IT Switching on continuous operation : □ Press the ON / OFF switch |T|, hold it pressed and press the locking button IT Switching off continuous operation: □ Press the ON / OFF switch [T] then release it again. • Setting the oscillation speed You can set the desired oscillation speed as needed with the oscillation speed selector Q0. The required oscillation speed depends on the material being worked and can be determined through practical tests. NOTE: Before attaching a new sanding pad [9], remove dust and dirt from the sanding plate IT. Sanding sheets with hook and loop fastening: □ Fix one side of the sanding sheet [9] flush with one side of the backing plate T. □ Then attach the sanding sheet [9] to the backing plate |T and press it firmly into place. Sanding sheets without hook and loop fastening: □ Open the two clamping levers IT. □ Push one end of the sanding sheet |T under the open clamping bar [6] and clamp the sheet firmly in place by locking the clamping lever |T back in place. □ Repeat this procedure at the other end. Various materials require different grit values. You can read which grit value is best suited for which work in our recommendations under "Instructions, tips and tricks". • Vacuuming dust AkJWARNI NGmGEEEASAES A risk of fire exists when working with electrical appliances that have a dust collection box |T or can be attached to a vacuum cleaner via an external suction adapter! Under certain conditions the sanding dust in the dust box (or in the vacuum's dust bag) may self-ignite, e.g. as a result of flying sparks generated when abrading metals or metal objects left in wood. This can happen especially if the wood dust has paint particles on it or is mixed with other chemical substances and the sanded material is hot after extensive working. You should therefore avoid overheating of products being sanded as well as the appliance and always empty the dust collection box |T or the dust bag of the vacuum cleaner before work pauses. • Attaching a sanding pad ^^ArNinGI Before performing work on the ^ Wear a dust mask! appliance, always disconnect the power. 10 GB/IE III PARKSIDE Operation / Maintenance and cleaning Vacuuming dust with the dust collection box Attach the dust collection box: □ Push the dust collection box [4 on to the device. Remove the dust collection box: □ Press the release button(s) [3 and pull the dust collection box [4 off the device. NOTE: Always empty the dust collection box [4 in due time and shake any remaining dust out; this will ensure optimal vacuum performance. Dust extraction using an external vacuum extraction device Connecting: □ For vacuum ...