Оценок - , средний балл:
(
)
)
Производитель: Parkside
Размер: 2.1 mb
Название файла: 8400812a-3f5f-4265-99a6-e5e9bc2bda73.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
The use of tools and accessories other than those recommended in the operating instructions could lead to an increased risk of personal injury for you. Q Operation Q Operation Take note of the mains voltage! The voltage must agree with the information on the type plate of the appliance (appliances that are designated as 230 V can also be connected to 220 V). Q Switching On and Off Switching on intermittent function: j Press the ON/OFF switch 1 . Switching off intermittent function: j Release the ON/OFF switch 1 . Switching on continuous operation : j Press the ON/OFF switch 1 , hold it pressed and press the locking button 2 . Switching off continuous operation: j Press the ON/OFF switch 1 then release it again. Q Setting the oscillation speed You can set the desired oscillation speed as needed with the oscillation speed selector 10 . The required oscillation speed depends on the material being worked and can be determined through practical tests. Q attaching a sanding pad WarNING! Before performing work on the appliance, always disconnect the power. NOTE: Before attaching a new sanding pad 8 .9 , remove dust and dirt from the sanding plate j Fix one side of the sanding sheet flush with one side of the backing plate 8 . j Then attach the sanding sheet to the backing plate 8 and press it firmly into place. Sanding sheets with hook and loop fastening: 99 Sanding sheets without hook and loop fastening: j Open the two clamping levers 7 . j Push one end of the sanding sheet 9 under the open clamping bar 6 and clamp the sheet firmly in place by locking the clamping lever 7 back in place. j Repeat this procedure at the other end. Various materials require different grit values. You can read which grit value is best suited for which work in our recommendations under “Instructions, tips and tricks”. Q Vacuuming dust WarNING! FIrE HazarD! A risk of fire exists when working with electrical appliances that have a dust collection box 4 or can be attached to a vacuum cleaner via an external suction adapter! Under certain conditions the sanding dust in the dust box (or in the vacuum’s dust bag) may self-ignite, e.g. as a result of flying sparks generated when abrading 10 GB/IE/CY Operation metals or metal objects left in wood. This can happen especially if the wood dust has paint particles on it or is mixed with other chemical substances and the sanded material is hot after extensive working. You should therefore avoid overheating of products being sanded as well as the appliance and always empty the dust collection box 4 or the dust bag of the vacuum cleaner before work pauses. Wear a dust mask! Vacuuming dust with the dust collection box attach the dust collection box: j Push the dust collection box 4 on to the device. remove the dust collection box: j Press the release button(s) 3 and pull the dust collection box 4 off the device. NOTE: Always empty the dust collection box 4 in due time and shake any remaining dust out; this will ensure optimal vacuum performance. Dust extraction using an external vacuum extraction device Connecting: j For vacuum dust removal using a vacuum cleaner, push the suction hose of a vacuum cleaner approved for use as a dust extraction device (e.g. a workshop vacuum cleaner) into the connection 5 – see Fig. D. NOTE: If it is necessary to use the reducer piece 12 , push the reducer piece into the connection 5 . removing: j Pull the hose of the dust extraction device off the connection 5 or off the reducer piece 12 , Q Instructions, tips and tricks j Move the oscillating sander parallel, in flat circles or alternating between lengthwise and side-to-side motions. j Do not press down with the oscillating sander. The sanding pads become clogged, which reduces the sanding performance. j Clean the sanding pad 9 occasionally with the vacuum cleaner. j The removal performance and therefore the result of your work are determined by the correct selection of the speed and sanding pad 9 grit. j Never sand different materials with the same sanding pad 9 (e.g. wood then metal). The following table offers some values, which are for information only and may simplify the selection of a sanding pad 9 . Wood Sanding Pad / Grit Sanding of wood 40 -240 Pre-sanding, e.g. of rough, unplaned beams and boards 40, 60 Surface sanding 80, 100, 120 Fine sanding of hard woods 180, 240 Paints / Lacquers Sanding Pad / Grit Sanding of paint / lacquer coats or base coats such as filler and smoothing compound 40 -320 Sanding off paint 40, 60 Sanding off primer coats 80, 100, 120 Final sanding of base coats before painting 180, 240, 320 if one is used. GB/IE/CY 11 Maintenance and cleaning/Service centre/Warranty/Disposal Q Maintenance and Cleaning WarNING! DaNGEr OF INJUry! Before performing any work on the appliance, disconnect the power plug. j Clean the appliance regularly, preferably always immediately after use. j Do not use any sharp objects for cleaning the appliance. Never permit fluids to permeate inside the appliance. j ...