Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
11. Check that the workpiece is properly supported. 12. Pay attention that the wheel continues to rotate after the tool is switched off. 13. This tool has not been waterproofed, so do not use water on the workpiece surface. 14. Ventilate your work area adequately when you perform sanding operations. 15. Use of this tool to sand some products, paints and wood could expose user to dust containing hazardous substances. Use appropriate respiratory protection. SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. FUNCTIONAL DESCRIPTION FUNCTIONAL DESCRIPTION 1 2 1. Switch trigger 2. Lock button 003438 1 2 3 1. Switch trigger 2. Adjusting dial 3. Arrow indication Number RPM 1 1,500 2 1,750 3 2,000 4 2,300 5 2,550 6 2,800 CAUTION: • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Switch action CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” position when released. • Switch can be locked in “ON” position for ease of operator comfort during extended use. Apply caution when locking tool in “ON” position and maintain firm grasp on tool. To start the tool, simply pull the switch trigger. Release the switch trigger to stop. For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigger fully, then release it. Speed adjusting dial The tool speed can be changed by turning the speed adjusting dial to a given number setting from 1 to 6. Higher speed is obtained when the dial is turned in the direction of number 6. And lower speed is obtained when it is turned in the direction of number 1. Simply align any number setting with the arrow indicator. Refer to the table for the relationship between the number settings on the dial and the approximate tool speed. High speed: For sanding operation Low speed: For polishing operation CAUTION: • If the tool is operated continuously at low speeds for a long time, the motor will get overloaded, resulting in tool malfunction. • The speed adjusting dial can be turned only as far as 6 and back to 1. Do not force it past 6 or 1, or the speed adjusting function may no longer work. ASSEMBLY ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 003446 Installing side grip (auxiliary handle) CAUTION: • Always be sure that the side grip is installed securely before operation. Screw the side grip on the tool securely. The side grip can be installed on either side of the tool, whichever is convenient. 1. Grip Installing or removing abrasive disc Mount the rubber pad onto the spindle. Fit the abrasive disc on the rubber pad and screw the lock nut onto the spindle. 1 1. Lock nut 1 3 2 003455 2. Abrasive disc 3. Rubber pad 003456 To tighten the lock nut, hold the spindle with the wrench so that it cannot revolve, then use the lock nut wrench and securely tighten clockwise. To remove the disc, follow the installation procedure in reverse. 1 2 1. Lock nut wrench 2. Wrench 1. Wool bonnet 2. Lock nut 3. Rubber pad 1 2 3 003463 15 1. Wool bonnet 2. Lock nut 3. Rubber pad 1 2 3 003463 15 003461 Installing or removing the wool bonnet (optional accessory) Mount the rubber pad onto the spindle. Screw the lock nut onto the spindle. To tighten the lock nut, hold the spindle with the wrench so that it cannot revolve, then use the lock nut wrench and securely tighten clockwise. Fit the wool bonnet completely over the rubber pad and pull the string tight. Tie a bow knot and tuck the knot and any loose strings between the wool bonnet and the rubber pad. To remove the wool bonnet, follow the installation procedure in reverse. OPERATION 003472 Sanding operation CAUTION: • Always wear safety goggles or a face shield during operation. • Never switch on the tool when it is in contact with the workpiece, it may cause an injury to operator. • Never run the tool without the abrasive disc. You may seriously damage the pad. Hold the tool firmly. Turn the tool on and then apply the abrasive disc to the workpiece. In general, keep the abrasive disc at an angle of about 15 degrees to the workpiece surface. Apply slight pressure only. Excessive pressure will result in poor performance and premature wear to abrasive disc. 003476 15 003476 15 MAINTENANCE 001145 1 1. Limit mark 003481 1 2 1. Screwdriver 2. Brush holder cap Polishing operation CAUTION: • Always wear safety glasses or a face shield during operation. Hold the tool firmly. Turn the tool on and then apply the wool bonnet to the workpiece. In general, keep the wool bonnet at an angle of about 15 degrees to the workpiece surface. Apply slight pressure only. Excessive pressure will result in poor performance and premature wear to wool bonnet. CAUTION: • Always be sure that the tool is switche...