Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
ASSEMBLY INSTRUCTIONS Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 12. CAUTION: Always make sure the Power Cord (26) of the Sander is unplugged from its electrical outlet prior to making any adjustments or assembling to the tool. ATTACHING THE DUST BAG (12) To attach the Dust Bag (12) to the Palm Sander, place the opening of the Dust Bag (12) on top of the opening of the Dust Port of the Palm Sander and press down. Snap it in place into the rectangular shaft at the back of the Sander. The Dust Collection Chute will only work if the sandpaper has holes that line up with the 6 dust collection holes in the Backing Pad (22). (There are 4 other holes in the Backing Pad for the Screws). ATTACHING SANDPAPER TO THE BACKING PAD (22) Press the tab on the Clamps (17) inward on both sides of the unit and swing the clamps on both sides up, out, and down to loosen the clamp. See 1 & 2, right. Cut the sandpaper to fit the 4” W x 41/2” L Sanding Pad (22), with a little extra to overlap and fit under the Clamps (17). Do not use torn or frayed sandpaper. After wrapping the overlapped edges of sandpaper under the Clamps (17), snap the Clamps (17) back into place. HOW TO USE THE SANDPAPER HOLE PUNCH (29) Mount the Sandpaper Hole Punch (29) to a work bench using two counter sinking screws (not included). Press the sander (with the sandpaper attached to it), straight down onto the Sandpaper Hole Punch. Use the corner guides, on the Hole Punch, to assure the holes line up with the holes in the Backing Pad (22) of the Sander. Sandpaper goes under here REV 02/07 OPERATING INSTRUCTIONS Note: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 12. CAUTION: Always make sure the Power Cord (26) of the Sander is unplugged from its electrical outlet prior to making any adjustments to the tool. Clamp your workpiece down, or insert it in a vise. Make sure the object you are sanding does not have any nails or metal of any kind in it, or you will ruin the sandpaper and damage the Backing Pad (22). After donning the appropriate safety gear covered on page 2 of this manual, plug in the Sander. Turn on the Palm Sander by turning on the Switch (3). Always run the Palm Sander for a few seconds before contacting the workpiece. Contact the workpiece with minimal pressure. If the Palm Sander is not removing enough material, try a grittier piece of sandpaper. If you want to remove a lot of material fast, use a belt sander. Note: All orbital sanders leave sanding marks on the workpiece. To minimize sanding marks, slowly move the Palm Sander while it is touching the item you are sanding. Occasionally stop the Palm Sander and visually check the sandpaper for tears, wear, or fraying. Replace if necessary. When you are finished sanding, turn off the Switch (3). INSPECTION, MAINTENANCE, AND CLEANING WARNING! Make sure the Power Switch (3) of the Sander is in its “OFF” position and that the tool is unplugged from its electrical outlet before performing any inspection, maintenance, or cleaning procedures. BEFORE EACH USE, inspect the general condition of the Sander. Check for loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. If abnormal noise or vibration occurs, have the problem corrected before further use. Do not use damaged equipment. Wipe the unit down after each use with a dry, lint free cloth. Make sure the vents on the top are clear of dust and debris. Periodically, have a qualified service technician clean or replace the Carbon Brushes (9). PARTS LIST PartDescriptionQ’ty1Bottom Enclosure12Top Enclosure13Switch14Stator15Rotor and Fan16Rubber Cylinder47Switch Cover18Brush Holder29Carbon Brush210Bearing 6 x 19 x 6111Bearing 9 x 26 x 8112Dust Bag113Balance Fan114Bottom Board115Screw M4 x 82PartDescriptionQ’ty16Gasket217Clamp Wire218Bearing 12 x 28 x 8119Ring120Gasket121Screw M4 x 12122Backing Pad123Cord Anchorage124Screw ST3 x 12225Cord Guard126Power Cord and Plug127Label228Screw ST 4.2 x 19429Sandpaper Hole Punch 1Record Product’s Serial Number Here: Note: If product has no serial number, record month and year of purchase instead. Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. 3491 Mission Oaks Blvd. • PO Box 6009 • Camarillo, CA 93011 • (800) 444-3353Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of ninety days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, or to lack of maintenance. We shall in no...